Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Atosa refrigeration and cooking equipment repair in the Twin Cities

Atosa reach-in, prep table and CookRite fryer, griddle and range repair on site in Minneapolis, St. Paul and the surrounding metro. Written estimate first.

(651) 395-3422
Quick answer

What fails most often on Atosa equipment?

On Atosa refrigeration the usual failures are a clogged condenser, a worn gasket, a failed fan motor and a probe or controller fault. On the CookRite cooking line, thermostats, pilot assemblies and igniters, and burner problems are the common calls. Gas and live electrical work should be left to a technician.

About Atosa equipment

Atosa is a value-priced commercial equipment brand sold in the United States through dealers and online. In Twin Cities restaurants it tends to show up in new independent kitchens, taquerias, pizzerias and fast casual start-ups, where the budget favors a lower-cost reach-in or a CookRite fryer or griddle. The line covers refrigeration and cooking, which is why it is listed in both categories.

Servicing Atosa differs from servicing a legacy American brand because there is less published service history to lean on, and parts must be matched carefully. A reach-in cooler repair is usually a standard sealed-system job. On the cooking side, a griddle repair or a fryer call on a CookRite unit is a gas appliance job, with thermostats and burners that are common types.

Atosa reach-in refrigerators and freezers

Seen on this line: Condenser coil clogged / Fan motor failing / Probe or controller fault

Atosa reach-ins use top-mounted condensing units and electronic controls. The usual faults are a coil loaded with kitchen grease, evaporator and condenser fan motors, gaskets that harden, and a probe that reads wrong. Doors on busy stations loosen over time. After diagnosis, the question is whether the cost of the repair fits a lower-cost cabinet. Newer units may use R290, which changes how the sealed system is serviced. The cabinets are straightforward, which suits a small kitchen, though a condenser that is never cleaned will shorten the life of any of them. Check that the cabinet has room to breathe and that doors close fully.

Atosa sandwich, salad and pizza prep tables

Equipment guide

Prep Table Repair

Seen on this line: Warm rail / Plugged condensate drain / Hinges and lids worn

MSF sandwich prep tables and MPF pizza prep tables are common in small kitchens. A warm rail comes from blocked airflow or a slow fan. Standing water comes from a plugged drain. Heavy daily use wears lids and hinges. Pizza prep tables carry a larger top for dough and toppings, and a heavy load of cold toppings blocks the airflow around the rail. Keep the pans below the fill line, close the lids when idle, wipe the gasket, and let a recently stocked rail pull down before service starts.

Atosa CookRite fryers

Seen on this line: Pilot or igniter will not hold / Thermostat drift / High-limit tripping

CookRite gas fryers rely on a pilot or igniter, a gas valve, a thermostat and a high-limit. The usual faults are a pilot that will not hold, a thermostat that drifts, a high-limit that trips and burners fouled by overflow. A fryer that will not light is a safety question: if you smell gas, leave and call the gas utility from outside. Gas fryers need clean burners and a steady gas supply, and a unit that has been moved may have a disturbed connection. Do not adjust the gas valve. A fryer that smells of gas must be shut off at the appliance valve if you can reach it safely, and the building left until the utility clears it.

Atosa CookRite griddles

Seen on this line: Cold spots from clogged burner ports / Thermostat failure / Grease in the burner compartment

CookRite griddles use gas burners under a steel plate with thermostatic or manual control. Cold spots come from clogged burner ports or a warped plate, and a failed thermostat gives uneven heat. Grease in the burner compartment is a recurring cause. On many griddles a manual valve and a thermostat control each section. A section that stays cold may have a blocked orifice, and a section that is too hot may have a failed thermostat. Clean the grease trough and burner compartment regularly, since built-up grease is both a heat problem and a fire concern.

Finding the model and serial plate

The Atosa model and serial plate is usually inside the cabinet on refrigeration and on the rear, side or underside of cooking equipment. Have the full model, the serial number, the voltage and, for cooking equipment, the gas type, natural or propane. Note whether the unit is from the refrigeration line or the CookRite line.

Parts

Atosa parts are ordered by model and serial number through the distributor or importer. Common parts such as motors, capacitors, thermostats and igniters are often generic, while panels, doors and controllers need a match. Because the brand is imported, lead time can vary by item and supplier. Have the model and serial ready before you call.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Atosa repair questions

What is Atosa CookRite?

CookRite is Atosa's cooking equipment line, which includes gas fryers, griddles, ranges and charbroilers. It sits alongside the Atosa refrigeration line, which is why the brand appears under both refrigeration and cooking. Check the data plate to see which line a unit belongs to.

Why will my Atosa fryer not stay lit?

A pilot that goes out is usually a dirty pilot assembly, a weak thermocouple or a draft. Do not relight repeatedly. If you smell gas, leave and call from outside. Otherwise, call for service on the pilot and valve.

Is a cheap cabinet worth repairing?

It depends on the failure. A fan motor, capacitor or gasket is an ordinary repair. A failed compressor on an older lower-cost cabinet may not be worth it. The written estimate gives you the numbers to compare.

Why is my Atosa griddle heating unevenly?

Clogged burner ports, a warped plate or a failing thermostat are the usual causes. Grease in the burner compartment blocks the flame. Let the unit cool, then call. Never try to clear a gas burner with anything but a technician present.

Can I use any gasket on an Atosa door?

No. Gasket profiles differ between models and the wrong one will leak. Order by model number, and install it fully seated in the groove or channel. The same applies to hinges and fans, which are matched to the model.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422