Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Pitco fryer repair in Minneapolis and St. Paul

On-site Pitco fryer repair in the Twin Cities: Solstice and tube-fired gas fryers, electric models, millivolt pilots, thermostats and built-in filtration.

(651) 395-3422
Quick answer

Why will my Pitco fryer not stay lit?

On a Pitco gas fryer that will not stay lit, the cause is usually the pilot and safety circuit: a dirty pilot, a weak thermopile, a failing millivolt gas valve or a tripped high-limit. Solstice models use an ignition module instead. A gas smell means leave and call the utility.

About Pitco equipment

Pitco is a gas fryer brand first. Its tube-fired fryers have been in restaurants, bars, school kitchens and convenience store food counters for decades, and a lot of old floor-standing 35-pound and 40-pound units still run. The Solstice line of infrared-burner gas fryers is the newer generation, and Pitco also builds electric fryers with hinged elements. If you cook fries, wings, fish or breaded product in a Twin Cities kitchen, there is a fair chance a Pitco is in the line.

What separates a Pitco repair from other makers is the control system on the fryer in front of you. Many older gas models run on millivolt: a standing pilot heats a thermopile that powers the gas valve with no outside electricity, so a fryer will cook through a power outage. Solstice and newer designs use electronic ignition and a control board. We start every commercial fryer call by identifying which kind you have, and the fryer that will not stay lit guide covers the pilot side in more depth. Frymaster and Henny Penny are the closest comparisons.

Pitco tube-fired gas fryers

Seen on this line: Weak thermopile or failing millivolt gas valve / Carbon on pilot orifice and soot in tubes / Thermostat or high-limit out of calibration

The classic Pitco gas fryer burns gas inside steel tubes that pass through the oil, and the flame is lit by a standing pilot. A thermostat with a capillary bulb in the oil opens and closes the main gas valve, and a separate high-limit shuts the unit down if the oil overheats. When one will not stay lit, the sequence is: pilot flame size and colour, thermopile millivolt output under load, the safety magnet in the gas valve, then the thermostat and high-limit. Carbon on the pilot orifice and soot inside the tubes are common in fryers that are never boiled out. Tube fouling reduces recovery and shows up as soggy product at the dinner rush. All gas valve and orifice work is left to a technician and the gas supply side stays with the utility.

Pitco Solstice and electric fryers

Seen on this line: Ignitor and flame sensor wear / Controller probe or board faults / Contactor and element failures on electric models

Solstice fryers use an infrared burner under a smooth-tube design that aims to burn less gas per pound of product, with electronic ignition, a control board and a digital or solid-state controller. Failures move from the pilot to the board: ignitor wear, flame sensor fouling, a failed gas valve coil, blower or pressure switch faults on powered models, and probe failures that make the controller drop to a fault. Electric Pitco fryers use hinged-up heating elements, contactors and a thermostat, and the usual problems are burned contacts, a failed element, a tripped high-limit and sludge baked on the element surface. Electric units in schools and churches often have only one cook cycle a day and a lot of carbon build-up between uses.

Pitco built-in filtration

Seen on this line: Cold oil clogging pump and lines / Worn o-rings and quick-disconnects / Drain valve switch sticking and blocking ignition

Some Pitco fryers carry a built-in filter, usually marked with an S in the model, with a pan under the fry pots and a pump that returns clean oil. The problems are in the plumbing and the habits: a filter pan that is never cleaned, filter paper or pad installed with a fold, quick-disconnect o-rings that no longer seal, a drain valve that does not seat fully, and a pump that clogs with congealed oil. A drain valve safety switch on some models cuts the burner when the valve is open, so a fryer that will not light after filtering may simply have a sticking drain handle.

Finding the model and serial plate

The rating plate is usually inside the door or on the inside of the cabinet frame and lists model, serial number, gas type and input rating. Model strings such as SG14 or 35C+ carry the series, and an S usually means a built-in filter. Note whether the fryer has a pilot light or an ignition board, and the controller type, when you call.

Parts

Pitco parts come from the manufacturer and from foodservice parts distributors. Gas valves, thermostats and high-limits are model-specific because of gas type and temperature range, and controllers and boards are proprietary. Pilot assemblies, thermopiles, gaskets, o-rings and filter supplies are widely available. Lead times vary by part and series, and older models may need a substitute part. We confirm the part against the plate before ordering.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Pitco repair questions

How can I tell if my Pitco is millivolt or electronic ignition?

A millivolt fryer has a standing pilot flame behind a small window and often works with the power off. Electronic models click or glow when they start and do nothing if the power is out. The identification changes what we test first.

Why does our Pitco take longer to recover after dropping a basket?

Soot on the tubes or a thermostat reading low are the usual reasons. A boil-out cleans the pot but not the flue side, so a recovery problem after a clean pot points to the burner side. We also compare the thermostat against a test thermometer.

What does the S in a Pitco model number mean?

On many Pitco gas fryers it indicates a built-in filtration system. It matters for service, because the filter pump, pan and drain valve become part of the troubleshooting. Tell the technician when you call so the right parts come along.

Is it safe to relight the pilot ourselves?

If the procedure is on the fryer and nothing smells of gas, relighting a standing pilot is part of normal operation. If it goes out again right away, stop. A gas smell at a Pitco means everyone leaves, and the utility is called from outside.

Why does the oil seem to burn out faster on one of our two Pitcos?

A thermostat that runs hotter than set or a probe off its calibration cooks the oil harder. We check the actual oil temperature against the setpoint with a test thermometer, and we also look at how long the oil has been in service before blaming the fryer.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422