Blodgett convection, deck and combi oven repair in the Twin Cities
On-site Blodgett convection oven, deck oven, pizza oven and combi repair in Minneapolis and St. Paul. A written price to approve before work starts.
What fails most often on Blodgett ovens?
On Blodgett ovens the common failures are the pilot or ignition and the gas valve on deck and convection models, the blower motor and door switch on convection ovens, and thermostat or high-limit trouble on both. Combi models add steam and water problems. Deck ovens often fail slowly: a burner or thermostat drifts rather than quits.
About Blodgett equipment
Blodgett is a Burlington, Vermont, oven maker that dates back to 1848, and it builds convection ovens, deck ovens, pizza ovens and combi ovens. It is part of The Middleby Corporation, as are Southbend and Middleby Marshall. In the Twin Cities you see Blodgett in pizzerias, bakeries, school and hospital kitchens and hotels, most often as a stacked pair of DFG convection ovens or a deck oven in a pizza shop.
Repairing Blodgett means knowing which type of oven you have, since a DFG convection oven, a stone-hearth deck oven and a combi are three different machines with three different failure patterns, and the dial on the front rarely tells you which one you are dealing with. We work on all of them, from a commercial oven with a failed blower to a pizza oven that will not hold temperature to a combi oven that has stopped making steam.
Blodgett convection ovens: DFG, Zephaire and Mark V
Equipment guide
Seen on this line: Blower noisy, slow or seized / Door switch stuck so the fan stays off or on / Ignition control or pilot safety dropping out / Thermostat reading wrong or hot spots
The DFG-100 and DFG-200 are the best-known Blodgett gas convection ovens, and the Zephaire and Mark V lines cover other sizes and controls. They use a blower motor, a door switch, a thermostat or solid-state control, and a gas ignition system with a pilot safety. Typical failures are the blower motor and bearings, the door switch, the thermostat, the ignition control and the pilot. A convection oven that cooks unevenly often has a loose blower wheel, a bent baffle or a worn door gasket. A blower that runs slowly is a motor or capacitor problem. If the oven ignites and then goes out, the flame sensor or pilot safety is the first check.
Blodgett deck and pizza ovens
Equipment guide
Seen on this line: One deck will not heat while others do / Burner clogged or pilot out / Thermostat off from its dial / Deck stone cracked or damaged
Blodgett's deck ovens, including the stacked pizza ovens that run in pizzerias, use stone or steel decks heated by individual burners per deck and a thermostat for each. The weak points are the burner and pilot, the thermostat and the gas valve. A deck that is cold while the others work usually has a single failed thermostat or a clogged burner. The stone is also part of the story: cracked or damaged decks cook unevenly. The oven's mass means it recovers slowly, so a problem shows up as a slow preheat rather than a sudden failure. We recommend not relighting a pilot if there is any gas smell.
Blodgett combi ovens
Equipment guide
Seen on this line: Steam weak or missing from scale / Fill solenoid or water level sensor failing / Door gasket leaking steam / Fan motor or control board fault
Blodgett's combi ovens, such as the BCX line, combine a convection oven with a steam system. They need a water supply, a drain and a way to generate steam. Failures are scale in the steam system, a fill solenoid or water level sensor, a door gasket, a fan motor and the control board. Water quality is the main driver of steam-related problems. A combi that will not make steam has a scaled generator or a blocked fill. We use a manometer, a meter and the unit's service mode to diagnose.
Finding the model and serial plate
Blodgett ovens carry a rating plate with the model number, serial number, gas type and BTU or electrical rating. On convection ovens it is typically on the side panel or behind the lower front panel; on deck ovens it is on the side of the base or inside the control area. Have the model, serial number and fuel type ready. Stacked ovens have a separate plate for each deck or section.
Parts
Blodgett parts come through the manufacturer's parts channel. Many wear items such as thermostats, door switches, blower motors and pilots have compatible versions, but ignition controls, gas valves and combi boards should match the model. Older ovens and discontinued control boards can lengthen the search. We confirm the model and serial number before ordering so the part fits the gas type.
Manufacturer warranty
If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.
See also
Compared with
Guides
More cooking equipment brands
Blodgett repair questions
Why will one deck of my Blodgett pizza oven not heat?
Each deck has its own burner and thermostat, so a cold deck usually has a failed thermostat, a plugged burner or a pilot that went out. A technician tests the valve and burner for that deck. The stone should be checked at the same visit. If it is cracked, it can cause uneven cooking.
Why does my Blodgett DFG convection oven shut off the fan when I open the door?
That is normal. The door switch stops the blower when the door opens, for safety. If the fan will not restart when the door closes, the switch is stuck or misaligned. Do not bypass it.
My Blodgett oven preheats slowly. What should I check?
Check that the vents are clear and the door seals. A slow preheat can also come from a clogged burner, a weak pilot or a thermostat that has drifted. A technician checks the burner flame and gas pressure.
Does a Blodgett combi need special water?
Yes, combi ovens do better with filtered and often softened water. Scale builds in the steam system and causes most steam problems. The right water setup depends on your local water supply and on the model, and a technician can test the water before suggesting a filter.
Is it worth repairing an older Blodgett DFG convection oven?
Often yes. The ovens are built heavy and the parts are commonly available. A repair makes sense unless the cavity is rusted through or the cost of several parts passes the value. We compare the repair against the age and condition of the oven.
