Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Follett ice machine and dispenser repair in the Twin Cities

Follett Chewblet ice machine and dispenser repair on site: Symphony and Horizon series, augers, remote ice delivery, antimicrobial bins and water filters.

(651) 395-3422
Quick answer

What commonly goes wrong with Follett ice machines?

Typical Follett faults are scale in the evaporator barrel, worn auger and bearing parts, a clogged water filter or inlet screen, a failed dispenser sensor or switch, and problems in remote delivery lines. Because Chewblet ice is eaten, cleaning and sanitation faults matter as much as mechanical ones.

About Follett equipment

Follett is based in Easton, Pennsylvania and is known for Chewblet ice, a soft, compressed nugget that people chew. Its Symphony and Horizon machines and its ice and water dispensers are staples in hospitals, senior living, convenience stores and cafes, where ice is eaten and handled by patients or customers. Because of that, a Follett call is half mechanical repair and half sanitation. Our ice machine repair page covers what is common across brands. This page covers what is particular to Follett.

Follett does not make the typical cuber with a flat evaporator. Its machines freeze water on the inside of a barrel and an auger moves the ice up, compresses it and extrudes it. Many installations also separate the machine from the point of use: the ice maker sits in a back room and ice is carried to a dispenser through a delivery line. That makes a service call a question of where the fault is, in the machine, the line or the dispenser. For a comparison with other nugget makers, see Scotsman.

Follett Chewblet machines in Symphony and Horizon series

Equipment guide

Ice Machine Repair

Seen on this line: Auger or bearing noise at the base / Barrel scale raising load / Seal leaking water below the evaporator / Extruder head restricted by deposits

A Follett Chewblet machine works like a flake-and-compress system. Water freezes on a cooled barrel wall, a slow-turning auger scrapes it off, and the flakes are pressed through an extruder to form soft nuggets. The wear parts are the auger, the bearings and seals at the base, the gear drive and the extruder head. Scale on the barrel raises load, and a machine on unfiltered water may start to groan, slow down or shut off on overload. We pull the auger to inspect the bearing and seal when the noise starts or the ice becomes wet. Follett publishes its own descaling and sanitizing instructions for the series. They are important because the nugget path is narrow, and film in it affects both taste and output.

Follett remote-delivery ice systems and dispensers

Equipment guide

Ice Machine Repair

Seen on this line: Delivery line kinked or blocked / Dispenser level sensor stuck / Chute flap or switch worn / Machine stopped by a false full signal

Follett builds systems in which the ice machine is in one room and the dispenser or storage is elsewhere. Ice moves through a delivery line to the point of use, and a fault can be in the machine, the line or the dispenser. A kinked or damaged line stops delivery without any fault at the machine. A dispenser with a level sensor that is stuck sends the wrong signal back, so the machine stops. In hospitals and care homes, dispensers also have chutes, flaps and sensors that wear with use. When a unit does not dispense, the technician first sees whether ice is present at the source, then follows the path to find where it stops. That approach avoids replacing a machine when the problem is a line or a sensor.

Follett ice and water dispensers and storage bins

Equipment guide

Ice Machine Repair

Seen on this line: Dispense lever or paddle worn / Switch failing from moisture / Water filter clogged and flow low / Drain plugged, water in the bin

Follett dispensers and storage bins are designed for sanitary handling, and in many models the bin surfaces are treated with an antimicrobial additive. The dispensing chute, the paddle or lever and the drain are the parts that wear. In healthcare, dispensers sit in pantries and hallways where cleaning is frequent, so water gets into switches and wiring. The water filter on a combination ice and water dispenser also needs replacement on a schedule, and a clogged one cuts the flow to the machine. A technician checks the filter, the water inlet valve and the dispense mechanism. Cleaning chemistry matters, because a harsh product can damage the finish that carries the antimicrobial treatment.

Finding the model and serial plate

Follett puts a data plate on the machine or dispenser, and the model number encodes the series, capacity and cooling type. On remote systems there are separate plates on the ice maker, the dispenser and sometimes the delivery equipment, so record each one. Have the full model, serial number, voltage, and the water filter model ready. For a combined ice and water dispenser, note both the dispenser and the machine feeding it.

Parts

Follett parts are sold through its dealer and distributor network, and the series decides the auger, bearing, seal and extruder parts. Those parts are specific to the machine family and generation, and generic equivalents rarely exist for the auger assembly. Common electrical parts and some pumps and fans can be matched. Water filters are ordered by filter model. We identify the series from the data plate and quote parts after the diagnosis so you approve the work first.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Follett repair questions

What is Chewblet ice and why is it harder to service?

It is Follett's name for its soft, compressed nugget ice. The machine freezes water on a barrel wall and presses the flakes into nuggets. That means an auger, bearings, seals and gears, which wear differently from the valves and plates of a cuber.

Why does my Follett machine make ice but nothing reaches the dispenser?

On a remote system the fault may be in the delivery line or the dispenser sensor, not the machine. A kinked line or a stuck level sensor stops ice moving. Check that ice is at the machine and note where it stops.

How often does a Follett water filter need replacing?

Follow the schedule in the manual for your filter model, and replace earlier if flow drops or the ice smells off. A clogged filter starves the machine of water and lets the auger run with less lubrication from the ice.

Can I use any sanitizer in a Follett bin?

Use only a product the manufacturer lists for that bin. Antimicrobial bin surfaces and plastic parts can be damaged by harsh chemicals. Follow the dilution and rinse steps exactly, particularly in healthcare, where the ice goes to patients.

Why does my machine shut off with a loaded sound?

An overloaded drive is the usual reason, and it often traces to scale in the barrel or a bearing that is failing. Do not keep restarting it. Repeated restart attempts can damage the gear drive, so shut it off and call a technician.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422