Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Continental Girbau washer-extractor repair in the Twin Cities

Repair of Continental Girbau washer-extractors and dryers in the Twin Cities: HS and EH washers, coin control, drain valves, bearings and door locks.

(651) 395-3422
Quick answer

What are common faults on Continental Girbau washer-extractors?

On Continental Girbau washer-extractors the repeat faults are drain valves that stick, door lock and interlock problems, bearing and shaft seal wear, inlet valve faults and coin control or payment issues on vended models. Control messages generally point toward the door, level or drain circuit involved.

About Continental Girbau equipment

Continental Girbau is the North American arm of Girbau, a laundry equipment group headquartered in Vic, Spain. The US company is based in Oshkosh, Wisconsin, and sells washer-extractors, dryers and finishing equipment under the Girbau name. For repair work the useful split is between the HS high-speed washer-extractors and the EH models, with vended versions that use coin control, and on-premise machines that run programmed cycles.

Continental Girbau is a smaller name in the Twin Cities than Speed Queen or UniMac, which is why a tech should check the plate and the model line before ordering parts. The brand shows up in laundromats, apartment laundry rooms and some on-premise laundries. Work on it falls within commercial washer repair, with attention to controls and mount type. Parts ordering differs from the Alliance brands, and some older machines now need a careful search, so we compare the repair against repair or replace guidance before work.

HS and EH washer-extractors

Seen on this line: Drain valve fails so the machine does not extract / Door lock circuit stops the start of the cycle / Rear leak from the shaft seal

The HS series are high-speed extractors and the EH washers are Girbau's newer designs. Faults on either include the drain valve that sticks open or shut, door lock and interlock failures that stop the cycle, and shaft seals that leak water toward the bearings. Inlet valve screens clog with mineral scale. The machine's control shows a message when it sees a level, door or drain fault, and controls such as Inteli and Logi Pro appear on Girbau models. Because the mounting style differs by model, we confirm on the plate and in the manual whether the machine is meant to be anchored to a slab or sit on suspension, and we check its footing before blaming the drum bearings.

Girbau tumble dryers and coin-operated machines

Seen on this line: Coin mechanism jammed or not signaling start / Gas burner not lighting or dropping out / Dryer overheating from restricted exhaust

Girbau tumble dryers have gas and electric heating, a motor-driven drum and the usual thermostat and high-limit protection. In coin laundries the weak point is often the coin control, the mechanism or board that accepts money and starts the cycle. Coin Control manuals for Girbau washers describe how the mechanism is set up and tested, and a jammed coin or a misaligned mechanism can stop a washer that is otherwise sound. On the dryer side, lint restricts exhaust and overheats the drum, and igniters and sensors fail afterward. We test the payment device and wiring separately from the heating or drive faults.

Finding the model and serial plate

The data plate sits on the rear or back panel of Continental Girbau machines and lists the model, serial number, voltage, phase and amperage. Model names such as HS and EH are followed by a number that relates to capacity, so read the complete string. Have the control type and whether the unit has a coin control ready. A photo of the plate and the front panel helps us decide what parts to order.

Parts

Parts for Continental Girbau machines are ordered through its North American distribution and ordering is by model and serial number. Valves, belts and seals can have equivalents once dimensions are checked, while control boards, coin mechanisms and shaft assemblies are generally manufacturer parts. Because the brand's parts do not overlap with the Alliance brands, a quick plate check prevents ordering the wrong item.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Continental Girbau repair questions

What do HS and EH mean on a Girbau washer?

They are model families. HS machines are the high-speed washer-extractors and EH models are another Girbau washer range. The full model number on the plate, not the family letters, is what we use to order parts.

Why will my Girbau washer not start after I pay?

Either the coin mechanism or payment device did not signal the control, or a safety circuit such as the door is open. On vended machines we test the payment path first, then the door lock and interlock circuit.

Can a Girbau washer sit on any floor?

That depends on the model's mounting design. A machine meant to be anchored to a slab needs a proper reinforced pad. Check the manual and plate for the mount type before installing or moving the machine.

Does Continental Girbau share parts with Speed Queen or UniMac?

Not as a rule. Girbau is a separate manufacturer from the Alliance brands, so parts are matched to Girbau's own model and serial numbers. Only generic wear items such as some belts or fittings might cross over, and we confirm fit first.

Is it worth fixing an older Girbau machine?

It depends on the fault and parts availability. A valve, belt or seal on a sound machine is usually reasonable, but a failing drum bearing assembly on a machine with discontinued parts calls for a comparison against replacement cost.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422