Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

How to find the model number and data plate on commercial equipment

Where the data plate is on refrigerators, ice machines, ovens, fryers, dishwashers and dryers, and which details a repair technician needs from it.

(651) 395-3422
Quick answer

Where is the model number on commercial kitchen equipment?

Look for a metal or foil data plate. On refrigerators it is usually inside the cabinet or on the end wall. On ice machines and ovens it is on the back, side or inside the door or kickplate. The plate lists the model, serial number, voltage, phase, gas type and refrigerant.

Why does the technician need the model and serial number?

The model number tells a technician exactly what machine you have, and with it they can look up the wiring diagram, parts list and service procedure. Many manufacturers make several versions of the same-looking unit with different controls, voltages or refrigerants, and a part that fits one will not fit another. The serial number tells the date and sometimes the production run, which matters when a design changed mid-year, and it is what the manufacturer uses to check warranty.

The more complete the information you give when you call, the more likely the right part is brought to the visit and the more likely the repair is finished on the first trip. A photo of the data plate takes ten seconds and is better than reading it aloud, because model numbers use letters and numbers that are easy to mix up, such as 0 and O or 1 and I.

What does the data plate tell you?

A data plate is a label, usually aluminum, stainless or a printed foil sticker, riveted or glued to the equipment. It is required to list the electrical or gas rating so the installer can connect the machine correctly. Not every plate lists the same fields, but the ones below are the ones a technician cares about most.

The electrical rating shows voltage, phase, amperage and sometimes the minimum circuit ampacity and maximum fuse or breaker size. The phase matters: single-phase and three-phase machines with the same model family have different motors and controls. A gas appliance plate lists the gas type, natural gas or propane, and the manifold pressure and BTU input. Refrigeration equipment lists the refrigerant type and charge. Water-using equipment may list the required supply pressure.

Plate fieldWhat it tells usWhy it matters
Model numberExact product and configurationWiring diagram, parts list, controls version
Serial numberIndividual unit, usually with a date codeDesign changes during production, warranty
Voltage and phaseSupply the machine was built forCorrect motors, contactors, heaters, boards
Amps or kWElectrical loadDiagnosing overloads, sizing the circuit
Gas type and inputNatural gas or propane, BTU rating, manifold pressureCorrect orifices, valve and pilot parts
Refrigerant and chargeType and weight of refrigerantCorrect recharge, supply and recovery
Manufacture dateAge of the machineParts supersession, service life decisions

Where is the plate on refrigeration equipment?

On reach-in refrigerators and freezers, the plate is usually inside the cabinet on a side wall or the ceiling near the door opening, sometimes behind a shelf, and sometimes on the back of the unit. True units commonly carry the plate on the inside wall, and the plate on a prep table or undercounter often sits inside the cabinet near the door frame or beside the condensing unit compartment. On a bottom-mounted compressor, it may be on the compressor deck itself.

A walk-in is a few pieces, and each has its own plate. The box has a manufacturer label near the door, usually on a panel. The evaporator, often inside the box on the unit cooler, has its own plate on the housing. The condensing unit, outside or on the roof, has its own plate on the unit or inside the access panel. All three can matter, because the box maker and the refrigeration maker are often different companies. Give the technician the plate details for the evaporator and the condensing unit, plus the box maker's name if you have it.

Display cases and bar coolers usually carry a plate on the back, bottom or inside the cabinet near the controls. Remote systems have a plate at the rack, not just on the case. Our commercial refrigeration repair page lists the systems we service.

Where is the plate on ice machines, ovens and fryers?

Ice machines usually carry the plate on the back panel or the side of the head section, and sometimes inside the cabinet behind a front panel. If the machine is stacked on a bin, the head and the bin are separate pieces, each with a plate, and you need the plate for the machine itself. A modular head on a bin with a separate remote condenser has a third plate on the condenser. For Manitowoc and similar machines, the model and serial number often appear on a label on the back and on the inside of the control area. The ice machine repair page covers what else to note.

Ovens, ranges and fryers carry the plate on the back or the side, near the gas connection or power cord, or inside the door frame or behind the kickplate or control panel. Convection ovens often have it on the right side panel or inside the lower door frame. Gas fryers have a plate on the cabinet front panel behind the door or on the back. Ranges have it on the front frame under the burner area or behind the lower kickplate.

Pizza ovens and deck ovens usually carry the plate on the front frame or the side. A conveyor oven carries it on the back or the end. If the plate is too worn to read, a flashlight and a photo from an angle can bring up stamped numbers.

Where is the plate on dishwashers, laundry and prep equipment?

Door-type and conveyor dishwashers usually have the plate on the side or the front panel of the machine, often on the lower front or behind a service panel, and under-counter machines usually have it inside the door frame or on the side. Hobart machines commonly carry the plate on the side or the front near the base, and the booster heater, if separate, has its own plate. For a dish machine, the plate also lists the electrical load of the booster heater and the water requirements. See the commercial dishwasher repair page for the checks we make.

Commercial washers and dryers have a plate on the back or on the inside of the loading door frame, and often a second label near the control panel. Mixers have it on the back or the base. Slicers carry it on the underside or the rear of the base. Coffee and beverage machines have it on the back, the bottom or inside the front door. Soft serve and frozen drink machines usually have it behind a side or rear panel and on the compressor compartment.

EquipmentUsual plate locationAlso useful
Reach-in or undercounter refrigeratorInside cabinet wall, ceiling or door frameController model, refrigerant
Walk-in cooler or freezerSeparate plates on box, evaporator and condensing unitBox maker, refrigerant, voltage
Ice machineBack or side of head, inside the front panelBin model, remote condenser plate, water filter
Oven, range or fryerBack or side near the connection, inside the door frame or kickplateGas type, manifold pressure
Door-type or conveyor dishwasherSide or lower front panel, booster heater separateBooster model, voltage, water temp
Washer or dryerBack panel or inside the door frameGas or electric, voltage, controller type

What if the plate is missing, painted over or unreadable?

It happens, especially on older equipment, equipment that was moved or refinished, and equipment that gets steam and grease. If the main plate is gone, look for a second label: many manufacturers stamp the model on a frame or a hidden panel, or put a second sticker in a different spot. A compressor, a motor, a control board and a gas valve each have their own labels with part numbers that can identify the machine.

If you cannot find any, take photos of the whole unit from the front, back and inside, the controls, the brand name and any logos, and measure the width, depth and height. A technician can often identify the model from that. Check the paperwork too: an original invoice, a delivery sheet, an install record or a warranty card lists the model and serial number. A photo taken at install time is the best insurance.

Whatever you do, do not guess. A wrong model leads to the wrong parts and a second visit. If a plate is damaged, record what is readable and say so on the call.

What should I have ready when I call?

A short list saves time on the phone and on the job. Have the brand, the model and serial number from the plate, the voltage and phase, the gas type if gas, and the refrigerant if refrigeration. Say what the machine is doing, when it started and what changed beforehand. Include any error code on the display and any steps you have already taken.

Keep a simple equipment list in the kitchen office or on your phone with the model and serial number for each machine, so you have it before the next failure. When a machine is old, the list helps with the decision in repair or replace, because you can check the age from the serial number and the manufacturer.

A safe sequence to follow

  1. Look for a metal or foil label

    Check the back, the sides, inside the door frame and behind kickplates and access panels.

  2. Photograph the whole plate

    Take a clear, straight-on photo, and a second from an angle if the print is worn.

  3. Read out model and serial

    Write down the model and serial number exactly, noting letters such as O and I versus digits 0 and 1.

  4. Note the utilities

    Record voltage and phase, gas type and refrigerant from the plate.

  5. Check separate pieces

    For walk-ins, stacked ice machines and dish machines with boosters, photograph each plate.

When to stop and call

  • You cannot find any plate and the machine needs a repair.
  • The plate is painted over, corroded or unreadable.
  • The machine has been moved, rebuilt or had a part swapped, so the plate may not match.
  • You are unsure whether a gas appliance is set for natural gas or propane.
  • The plate shows a refrigerant or voltage you do not recognize.

Questions about this problem

Is the serial number the same as the model number?

No. The model number identifies the product design and configuration. The serial number identifies the individual unit and usually includes a production date code. A technician needs both, because parts can change within one model between production dates.

Why do walk-ins have three plates?

A walk-in is built from separate pieces: the insulated box, the evaporator inside and the condensing unit outside. They are often made by different companies, so each carries its own label. Photograph all three for the technician.

Can the age of the machine be read from the serial number?

Often, but the format varies by manufacturer. Some serials start with a year and month code, others use a letter code. The manufacturer's support line or the manual can decode it, and the plate sometimes also shows a manufacture date.

Does the plate say whether my oven runs on natural gas or propane?

A gas appliance plate lists the gas type it was built or converted for, along with manifold pressure and BTU input. If the plate and the actual supply do not match, stop and call a technician rather than using the appliance.

What if the data plate says one voltage and my building is different?

A mismatch is a problem and should be sorted before anything is repaired. Do not guess at wiring. Photograph the plate and the electrical panel label and have an electrician or technician confirm the supply.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422