Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Walk-in freezer icing up: why it happens and how to stop it

Why a walk-in freezer ices up: failed defrost heaters, termination switches, door infiltration and drain line problems, with safe checks before you call.

(651) 395-3422
Quick answer

Why is my walk-in freezer icing up?

Ice builds when moisture gets in faster than the defrost cycle removes it. The usual causes are a failed defrost heater, timer or termination switch, a frozen or unheated drain line, a leaking door gasket, or a door left open. Where the ice forms points to the cause.

Why does a freezer make ice in the first place?

Every walk-in freezer makes frost. Air carries moisture, and the evaporator coil is the coldest surface in the box, so the moisture freezes on the coil fins. A small amount of frost is normal and is the reason freezers have a defrost system. At intervals, the system stops refrigeration and melts the frost off the coil. The water drains through a line out of the box. A healthy freezer runs this cycle several times a day without anyone noticing.

Icing becomes a problem when one of three things happens. More moisture gets in than usual. The defrost cycle fails to melt the frost completely. Or the meltwater cannot leave and refreezes. Each has a different cause and a different place to look, so start by noticing where the ice is: on the coil, on the drain pan and drain line, around the door, on the floor or on the ceiling and walls.

Where the ice isLikely causeWho fixes it
Solid block over the whole evaporator coilDefrost not happening or not completingTechnician
Ice in the drain pan or on the drain line, or a puddle outside the boxDrain line frozen or drain heater failedTechnician
Frost around the door frame and gasket, ice on the floor at the doorDoor gasket, door heater or door left openOperator and technician
Frost on the ceiling and walls, heavy fog when you open the doorMoisture getting in, door habits, vapor leaksOperator and technician
Ice on the fan blades or fan shroudFan blade out of position, coil iced overTechnician
Ice crystals on productTemperature swings or poor door habitsOperator

How does a defrost system work, and where does it fail?

Walk-in freezers almost always use electric defrost or hot gas defrost. In electric defrost, heater elements sit in or against the evaporator coil and a drain pan heater keeps the pan from freezing. In hot gas defrost, hot refrigerant from the compressor is routed through the coil. Off-cycle defrost, which relies on warm box air, works only in coolers above freezing and will not defrost a freezer.

A defrost system has a few parts that can fail. A defrost timer or control board starts the cycle at set times. A defrost heater melts the ice. A defrost termination thermostat or sensor ends the cycle once the coil is warm. A fan delay keeps the evaporator fan from blowing wet air into the box while the coil drips. If the timer fails, defrost never starts. If a heater fails, the cycle runs but the coil does not melt. If the termination switch fails open, the cycle may end too early. If it fails closed, the heaters can stay on too long and the box warms.

Heaters fail more often than people expect. One of several heater elements can burn out, melting part of the coil and leaving a pattern of ice that is clear above and thick below. A technician checks heater resistance and amperage, the timer or board, the termination sensor and the fan delay. This is high-voltage work, and the defrost parts are not safe for an operator to test. The guide on a walk-in cooler not cooling covers related symptoms on a medium-temperature box.

Why does the drain line matter so much?

The drain line carries meltwater out of the box. In a freezer, the line passes through a wall at below-freezing temperatures, so it has an electric heater, a heat trace cable or heater wire, wrapped along the pipe. If that heater fails, the water freezes in the line, backs up into the pan, overflows and freezes across the floor under the coil. This is one of the most common causes of ice on the floor of a freezer.

A drain line can also be blocked by debris, a missing or damaged P-trap or air trap, or insulation that has been crushed or removed. The trap matters: without it, warm outside air is pulled up the drain line into the box, which makes more frost. Never pour hot water down a frozen drain line, since it can crack plastic piping and refreeze farther down. And do not chip ice off the coil or the pan with a screwdriver or ice pick. A punctured evaporator coil is a refrigerant leak and a costly repair.

If you find a block of ice and the cause is not obvious, the safe step is to manually defrost by turning the box off, leaving the doors open and keeping product protected elsewhere, and to call for service. The ice will return if the failed part is not replaced.

How do doors and moisture cause icing?

Many cases of freezer icing are not equipment failures. They are moisture. Every time the door opens, warm humid air comes in, and the moisture freezes at the first cold surface, usually the evaporator and the area near the door. A door that is propped open, a strip curtain that is torn or missing, a door that does not close on its own or a gasket that no longer seals will do the same thing continuously.

Check the door first. A door should close and latch on its own from a few inches open. The gasket should be soft, unbroken and sealing all the way around, with no gaps at the corners. Look for frost lines on the gasket, which show where air is leaking. Many freezers also have a heater wire around the door frame to prevent the gasket from freezing to the frame. If the gasket is stuck solid, the heater may have failed. Replace torn gaskets promptly.

Also look at what goes in. Hot or uncovered, wet food adds moisture. Loading warm product, leaving boxes uncovered or putting steaming pans into a freezer adds vapor that freezes onto the coil. Stack product with space around the evaporator so air can circulate. A box packed tight against the coil blocks airflow, and frost builds fast where air stops moving.

What can the operator do safely, and what should wait for a technician?

Operators can do plenty without opening any panel. Check that the door closes, the gasket seals and strip curtains are intact. Look at where the ice is and take a photo. Clear product away from the evaporator. Note the box temperature and when it started to climb. Check that the breaker is on and the condensing unit is running. If the condenser is outdoors or on the roof, clear snow and leaves from around it when it is safe to reach. We do not repair building HVAC or rooftop units, but a walk-in's own condensing unit is part of the refrigeration system.

Leave anything electrical, refrigerant-related or behind a panel to a technician: defrost heaters, the timer or board, termination sensors, drain heaters, fan motors and any refrigerant line. Also leave the decision about defrosting. A planned manual defrost with product moved out is safe. An improvised one with a heat gun or a hose is not, because it can damage the coil, the floor and the insulation.

Which brands and box designs make this more or less likely?

Built-in freezers from makers like Kolpak, Nor-Lake and Master-Bilt all use electric or hot gas defrost with drain line heaters, and the parts are broadly similar from brand to brand, though heaters, timers and sensors are not always interchangeable between models. Older boxes with failing panels, damaged door frames or a floor that has absorbed water cause icing that no part replacement will cure. Wet insulation in a panel, or a frost heave in the floor, is a structural problem.

When you call, say where the ice is, when the box last defrosted properly, whether the evaporator fan is running and whether the door has been left open or loaded with warm product. Our walk-in freezer repair and commercial refrigeration repair pages describe what the technician will check on a visit.

A safe sequence to follow

  1. Look at where the ice is

    Note whether it is on the coil, the drain, the door or the floor, and take a photo.

  2. Check the door

    Confirm it closes and latches on its own, the gasket seals and strip curtains are intact.

  3. Clear airflow

    Move product away from the evaporator so air can circulate.

  4. Check power

    Confirm the breaker is on and the condensing unit and evaporator fans are running.

  5. Move product and call

    Protect frozen product in a working freezer and call a technician before attempting any defrost.

When to stop and call

  • The evaporator coil is covered in a solid block of ice.
  • Ice forms on the floor under the coil or around the drain.
  • The box will not hold temperature even with the door closed.
  • The evaporator fan is not turning or is turning slowly.
  • Ice returns within days of a manual defrost.

Questions about this problem

Is some frost on the evaporator normal?

Yes. A thin even layer of frost between defrost cycles is normal and melts during defrost. A thick or uneven layer that is still there after a defrost, or frost spreading to the fan, ceiling or floor, is not.

Why is there ice on the floor of my walk-in freezer?

Most often the drain line or its heater has failed, so meltwater backs up and freezes. A leaking door gasket or a missing strip curtain can also cause it. Check where the ice starts, then call for service.

Can I chip the ice off the coil?

No. Evaporator coil tubes and fins are thin and a puncture releases refrigerant. Turn the box off, move the product, leave the door open and let it melt, or have a technician do a controlled defrost.

What is the difference between a defrost timer and a termination switch?

The timer starts the defrost cycle at set times. The termination switch or sensor ends it once the coil is warm. If the timer fails, defrost never begins. If the termination fails, defrost may end too early or run too long.

Does a freezer need a different defrost than a cooler?

Yes. A medium-temperature cooler can use off-cycle defrost, relying on warm box air. A freezer is too cold for that, so it needs electric or hot gas defrost, plus heaters on the drain line to keep water from freezing.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422