Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Lincoln Impinger conveyor oven repair in the Twin Cities

Lincoln Impinger conveyor pizza ovens and countertop impingers repaired on site in the Twin Cities: finger plates, blowers, burners, belts and controls.

(651) 395-3422
Quick answer

What fails most often on a Lincoln Impinger oven?

On a Lincoln Impinger the usual failures are the air blower motor, the burner and flame supervision, the conveyor drive, and finger plates that are blocked or reassembled wrong. Grease and carbon buildup in the air path cause many of the rest, and they show up as uneven baking.

About Lincoln equipment

Lincoln Impinger is one of the best-known names in conveyor ovens, with a long line of floor models and countertop units. Lincoln Foodservice Products is based in Fort Wayne, Indiana, and the brand is now part of Welbilt, which Ali Group acquired in 2022. The Impinger is the oven you see in chain and independent pizza shops, sub and sandwich counters and delivery kitchens across the Twin Cities. A conveyor oven like this bakes with hot air blown through finger plates onto the product above and below the belt.

What sets a Lincoln apart from a stone deck is that the bake is a function of airflow, belt speed and temperature, and you can change all three. That also means most problems can be traced to one of them. A model from the 1100, 1400 or 1600 era may have a control or ignition design that differs from a current one, so the exact model matters more than the brand name. For pizzerias comparing ovens, our Bakers Pride page covers the deck side.

Impinger floor models: gas and electric

Equipment guide

Conveyor Oven Repair

Seen on this line: Oven locks out or will not light / Blower noisy, slow or tripping overload / Pizza bakes uneven side to side / Long preheat or will not reach temperature

Impinger floor ovens run a gas burner or electric elements, a large blower that pushes air through the plenums, and a wide conveyor driven by a gearmotor. On gas models a burner blower, an igniter and a flame sensor handle the fire, and a failure in any of them gives a lockout. The blower motor is the top wear item: a motor that runs hot, noisy or slow lengthens bake times and can trip an overload. Finger plates carry the jets of air to the pizza, and cleaning them in the wrong order or orientation changes how the oven bakes. A flame sensor that is dirty can cause repeated lockouts on an otherwise healthy burner.

Countertop Impingers

Equipment guide

Conveyor Oven Repair

Seen on this line: Element failure or one side runs cool / Blower rub, vibration or noise / Belt speed erratic or belt stops / Cooling fan intake clogged with grease

The countertop Impinger line is a smaller electric conveyor oven for shops that cannot fit a floor model, and the principles are the same: element, blower, belt, control. Their compact size means elements and blower motors run in tight spaces with less margin for heat. Problems include elements that fail or sag, blower wheels that rub, a conveyor motor that loses speed control and cooling fans that clog. These are 208 or 240 volt machines, so internal work is for a technician. Operators should keep the cooling intake and the area around the oven clear and clean.

Conveyor, belt and drive

Equipment guide

Conveyor Oven Repair

Seen on this line: Belt stops, slips or tracks off center / Drive chain, sprocket or bearing worn / Belt speed does not match the setting / Belt catches at the entrance or exit

The conveyor on an Impinger is a metal mesh belt driven by a gearmotor, with the belt speed setting the bake time. Belts stretch and track off center, and a belt that rubs the chamber opening wears and jams. Drive failures show as a belt that stops while the oven keeps heating, which burns whatever is inside, or a belt that runs at the wrong speed. Chains, sprockets and bearings wear and should be checked at regular service. Loading the belt with heavy pans or pushing a stuck belt by hand puts strain on the drive and can shear couplings.

Controls and temperature sensing

Equipment guide

Conveyor Oven Repair

Seen on this line: Display and chamber temperature disagree / Oven overshoots or swings widely / Control resets or shows erratic readings / Cooling fan stopped or intake blocked

Impinger controls range from older analog temperature controls and relays to later digital controllers with a sensor in the chamber. A sensor that reads wrong makes the oven overshoot or sit cold, and a loose connection mimics a bad sensor. Digital controls depend on a clean power supply, so a loose neutral or a weak breaker can cause resets that look like a control fault. Control compartments are cooled by a fan, and a blocked fan intake is the easiest way to shorten board life. Before replacing a control, a technician should verify the sensor, wiring and cooling.

Finding the model and serial plate

The Lincoln data plate lists the model number, serial number, fuel type, BTU or kilowatt input, voltage and phase. On floor models it is generally on the side or the back, and on countertop units on the back or underside. The model prefix, such as 1100, 1400 or 1600 for the older lines, tells us a lot about the controls and ignition design. Have the fuel type and voltage ready. Our model number guide explains the plate.

Parts

Lincoln Impinger parts include blower motors, burner assemblies, igniters and flame sensors, gas valves, sensors, control boards, gearmotors, belts, finger plates and cooling fans. Many parts depend on the model series and the fuel type, so we match them by model and serial. Some come only through the manufacturer or its distributors, and lead times depend on the part and supplier. We confirm the part number against the plate before we order, and we say where a suitable equivalent exists.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Lincoln repair questions

My Impinger bakes the front of the pizza differently from the back. What is wrong?

Check the finger plates first. Blocked openings or a plate put back in the wrong position changes the air pattern, and a pizza will bake unevenly as a result. Clean them with the oven off and cool, and replace them in the order they came out. If that does not fix it, have the blower checked.

How often should Impinger finger plates be cleaned?

Often enough that grease and carbon never build up. How often depends on what you bake and how heavily the oven runs. A shop running many pizzas a day needs more frequent cleaning than a sandwich shop. Plates that look glazed or have blocked openings are overdue.

Why does my Impinger shut down on a hot day?

Heat stress on the control compartment is a common cause. A blocked cooling fan intake, a failing fan or a hot kitchen with poor ventilation can make controls or limits shut the oven off. Clear the intake of lint and grease, keep the area around the oven open, and call if it recurs.

Is a gas Impinger different to repair than an electric one?

Yes. Gas models add a burner blower, a gas valve, an igniter and a flame sensor, and gas work is never an operator task. Electric ovens use elements and contactors at 208 or 240 volts. A Lincoln oven that smells of gas gets switched off at the shutoff only if safe, and the utility or 911 is called from outside.

Can I replace my own Impinger belt?

Belt replacement involves cooling the oven, disconnecting power and sometimes adjusting tracking, so it is best left to a technician. A belt installed with wrong tension or tracking will wear fast or jam. If the belt is damaged, stop using the oven so a snag does not tear it further.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422