Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Commercial kitchen equipment maintenance checklist by frequency

Daily, weekly, monthly and quarterly maintenance checklists for refrigeration, ice machines, cooking, warewashing and prep equipment in a kitchen.

(651) 395-3422
Quick answer

What maintenance does commercial kitchen equipment need, and how often?

Daily tasks are cleaning and reading temperatures. Weekly tasks are gaskets, drains and filters. Monthly tasks are condenser coils, burners and pump screens. Quarterly tasks are the items a technician should test: refrigerant, controls, gas and electrical. Frequency depends on the equipment family and the manufacturer's manual.

Why do most kitchen breakdowns trace back to missed maintenance?

A great many service calls come from the same short list of causes: a condenser coil packed with grease and lint, a drain that backed up, a door gasket that stopped sealing, a filter that stopped filtering and a scale-coated component that could not move water. None of them is a mystery, and all of them build slowly. The point of a checklist is to turn slow failures into a five-minute task before they become a service call during a rush.

The checklist below is split by frequency, and within each frequency by equipment family. Treat it as a baseline. Your manufacturer's manual overrides anything here, and a kitchen with heavy volume, grease-laden air or very hard water will need to do some tasks more often. Anything involving gas valves, high-voltage wiring, steam pressure or a sealed refrigerant circuit is not on the operator's list. Those items sit in the quarterly column for a technician, and refrigeration checks are covered on the commercial refrigeration repair page. A preventive maintenance visit is how many operators handle them.

What should be done every day?

Daily work is mostly observation and cleaning, and it is the cheapest maintenance there is. The reason to do it daily is that equipment tells you something is wrong before it stops. A fryer that takes longer to recover, a cooler that now reads three degrees warmer than last week and a dish machine that rinses with cloudy water are all warnings.

Write the temperatures down. A log with a date, a time, an initial and a reading for each cooler and freezer is also the first thing an inspector asks to see, and it is the first thing a technician wants when you call.

Equipment familyDaily taskWhat it prevents
Refrigeration (walk-in, reach-in, prep)Read and log the box temperature. Check doors close and gaskets are not folded. Wipe up spills near the evaporator and door.Warm product and unnoticed drifting temperatures
Ice machinesCheck ice is making and the bin scoop is stored clean outside the bin. Never use glass or a bare hand in the bin.Contamination and unnoticed production loss
Cooking (ovens, ranges, griddles, fryers)Clean cooking surfaces and burner area. Filter or skim fryer oil and check pilot or ignition behavior at start-up.Carbon and grease buildup, uneven heating
WarewashingDrain, clean scrap trays and screens, and check wash and final rinse temperature gauges.Clogged pumps, poor sanitizing
Prep (slicers, mixers)Clean and sanitize after use, check guards and the power cord.Cross-contamination and guard failures
Beverage (coffee, soft serve)Rinse and clean per the manufacturer's procedure. Check for leaks at fittings.Flavor problems and leaks

What should be done every week?

Weekly work is about the parts that wear or clog gradually. Gaskets collect food and mold, drains collect grease and debris, filters collect lint and grease, and spray arms, nozzles and strainers collect scale and food. None of this takes long, and it matters most in the places no one looks.

If you do only one weekly job, make it the door gaskets on every refrigerator and freezer. A torn or folded gasket lets warm humid air into the box, which makes the compressor run longer and causes ice on the evaporator. Pull each gasket back and look at the fold.

Equipment familyWeekly taskWhat it prevents
RefrigerationInspect and wipe door gaskets. Check that the drain line and drain pan are clear. Make sure product is not blocking evaporator airflow.Icing, water on the floor, warm spots
Ice machinesCheck the water filter indicator, wipe the exterior and look inside the bin for slime or pink film.Slime buildup and flavor complaints
CookingClean the oven cavity and door seal. Check fryer oil quality and the drain valve. Empty grease traps on griddles and charbroilers.Fires, off flavors, valve leaks
WarewashingRemove and clean wash and rinse arms, nozzles and curtains. Clean the strainer basket.Poor cleaning from blocked spray
PrepCheck slicer blade sharpness and the sharpener stone. Wipe mixer attachments and inspect the bowl lift.Dull blade injuries, jammed lift
LaundryClean lint screens and the lint trap or collection area. Wipe door seals on washers.Dryer fires, long dry times, mildew

What should be done every month?

Monthly work gets into the cooling and combustion systems. Condenser coils are the biggest item. A refrigeration condenser is a radiator, and when grease and dust coat it, the compressor cannot shed heat, runs hotter and fails years early. Cleaning a coil with a brush and a vacuum, with the power off, is within an operator's ability. Do not use a pressure washer on it. Water on a hot compressor compartment or on electrical parts is a separate problem.

Burners and pilot areas need a visual check for lazy yellow flames, soot, and debris. A burner that is mostly blue and even is healthy. Yellow tips or visible soot are a sign for a technician.

Equipment familyMonthly taskWhat it prevents
RefrigerationClean condenser coils or condenser filters, with power off. Check the walk-in door closer, strip curtain or door sweep.High head pressure, compressor stress
Ice machinesClean the air filter and check the condenser. Look at the water distribution system for scale.Slow production, hot condenser faults
CookingCheck burner flames for color and evenness. Check door hinges, latches and oven door gaskets. Check fryer thermostat behavior against a probe thermometer.Hot spots, poor combustion, temperature drift
WarewashingDelime the machine per the manufacturer if you have hard water. Check rinse aid and chemical feed lines.Scale on elements and lines
Prep and beverageCheck cord, plug and guard condition. Lubricate only where the manual says to.Electrical and mechanical wear
LaundryClean around and behind the machine. Check hoses for kinks and bulges.Leaks and floods

What belongs in the quarterly visit?

Quarterly is where a technician earns the visit, because these are the items that need gauges, meters and training. Refrigeration needs a check of refrigerant charge indicators, evaporator and condenser fan motors, defrost operation, and electrical connections. Ice machines need a full clean and sanitize by the manufacturer's procedure, at the interval the manufacturer sets. Gas equipment needs a combustion check: manifold pressure, flame quality, thermostat calibration, safety shutoffs and a check of the pilot and ignition parts. Electrical connections on motors, contactors and elements are checked for heat and tightness.

Water-side equipment needs its flow, pressure and temperature checked: dish machine booster heaters, steamer generators and boilers, and water softeners and filters. Steam equipment under pressure is checked for safety valves and low-water cutoffs. We service exhaust hoods, fans and make-up air (see hood and ventilation service), but fire suppression systems are inspected by a separate contractor on its own schedule, and the gas piping upstream of the appliance is the gas utility or a gas fitter's work.

Equipment familyQuarterly technician taskWhat it finds
RefrigerationFan motors, defrost heaters and termination, contactors, capacitors, charge check, door heatersFailing parts before the box warms up
Ice machinesFull clean and sanitize or descale, water flow and pressure, sensors, harvest cycle timingScale, bridging ice, failing probes
Cooking (gas)Manifold pressure, burner and pilot service, thermostat calibration, valve and safety checksWeak flames, drifting thermostats
Cooking (electric)Element resistance, contactor and wiring condition, thermostat calibrationHeat damage and weak elements
WarewashingBooster and tank heater function, pump and seal condition, chemical feed calibrationLow rinse temperature, leaking seals
Steam equipmentSafety valves, low-water cutoff, generator descaleScale and cutoffs failing

How do I make a checklist stick?

A checklist only works when someone owns it. Assign each task to a role, not a person, so it survives turnover: the opening cook reads the walk-in and the ice machine, the closing dishwasher does the strainers, the kitchen manager does the weekly gasket check. Post the sheet where it is used, next to the equipment, and have the manager initial it weekly.

Keep a short equipment record alongside it. Model, serial, install date and the dates of the last cleaning and service are the facts a technician needs and the facts that make finding the model number a one-minute job. Brand matters for specifics. Hobart warewashers, Hoshizaki ice machines and True coolers each have different cleaning procedures in their own manuals.

A safe sequence to follow

  1. Log temperatures at open

    Read and write down every cooler, freezer and warmer temperature at the start of the shift.

  2. Check door seals daily

    Look for folded, torn or dirty gaskets on every refrigerated door.

  3. Clean filters and screens weekly

    Pull and wash lint screens, strainers and drain screens on a fixed day.

  4. Clean coils monthly with power off

    Brush and vacuum condenser coils or filters with the unit unplugged or off at the breaker.

  5. Schedule the quarterly technician visit

    Book the tasks that need gauges and meters: charge, gas, combustion, electrical and water-side.

When to stop and call

  • A daily temperature reading is drifting up even though the doors and gaskets look fine.
  • A burner shows yellow flames, soot or a pilot that will not hold.
  • A coil or filter cleaning does not bring performance back.
  • A machine shows scale, leaks or unusual noise at its monthly check.
  • It has been a quarter since a technician looked at the critical equipment.

Questions about this problem

Can I clean a refrigeration condenser coil myself?

Yes, with power off. Use a soft brush and a vacuum, working along the fins, not across them. Do not use a pressure washer, which bends fins and soaks electrical parts. If the coil is inside a sealed compartment or leaking refrigerant oil, call a technician.

How often should an ice machine be cleaned and sanitized?

Follow the manufacturer's manual. Many call for cleaning and sanitizing at least twice a year, and more often in hard water or heavy use. Our guide on the ice machine cleaning schedule covers the procedure in detail.

What should a temperature log include?

Date, time, unit identifier, the reading and the initials of the person who took it, plus any action taken when a reading was out of range. A log that shows trends is the fastest way to spot a failing unit.

Which checks need a technician?

Anything that involves gas valves, manifold pressure, 208 to 480 volt wiring, sealed refrigerant circuits or pressurized steam is for a technician. Operators can safely clean, inspect, read gauges, check breakers and clear airflow around coils and vents.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422