Hoshizaki ice machine and refrigerator repair in the Twin Cities
Hoshizaki ice machine and refrigerator repair on site: crescent cubers, stainless evaporators, float switches, thermistors and cubelet machines.
What fails most often on Hoshizaki ice machines?
Typical Hoshizaki faults are a stuck or dirty float switch, a scaled evaporator, a failing water inlet valve, a weak circulation pump, and a thermistor or control board fault. Crescent cubers also depend on the right water flow during harvest, so low water pressure causes ice to stick.
About Hoshizaki equipment
Hoshizaki is a Japanese manufacturer, and its American operation is in Peachtree City, Georgia. It is best known for the crescent cube, a half-moon cube made on a vertical evaporator, but it also builds dice cube machines, flakers, cubelet machines and a full line of reach-in and undercounter refrigeration. That makes it one of the few brands on this site that fits two service categories. For the checks that apply to every make of ice machine, see ice machine repair. This page covers what makes a Hoshizaki different from the other cubers.
In Minneapolis and Saint Paul, Hoshizaki shows up in sushi and Asian restaurants, bars, hotel kitchens, hospitals and school cafeterias. Its stainless steel evaporator and its harvest method are what separate it from a grid-style machine like Manitowoc. A Hoshizaki relies on water to assist the harvest and on a thermistor to end it, so its diagnostic path is different, and its refrigerators share the same attention to simple reliable controls.
Hoshizaki crescent cube machines
Equipment guide
Seen on this line: Float switch sticking or coated with scale / Thermistor reading off and cycles running short or long / Water valve weak, ice not dropping at harvest / Circulation pump slowing and cubes forming unevenly
A Hoshizaki crescent cuber builds ice on a vertical stainless steel evaporator that has individual cups, and the cubes come out as half-moons. Where other brands sense thickness with a probe, the Hoshizaki control relies on a thermistor on the evaporator outlet, which tells the board the freeze is done when the line temperature falls to a set point. During harvest, the machine runs hot gas and opens the inlet water valve so water runs across the plate to help the cubes release. If the water valve is weak or the supply pressure is low, the ice may not drop and the machine sees a long harvest. A reed-style float switch in the reservoir tells the board when the water is at level. Sticking floats and scaled stems cause refill faults.
Hoshizaki dice, flake and cubelet machines
Equipment guide
Seen on this line: Auger bearing wear on cubelet and flake machines / Barrel scale raising motor load / Seal leak at the base of the evaporator / Dice cube machine slow to harvest on hard water
Beyond the crescent, Hoshizaki sells dice cube machines for beverage programs, flakers for food display and healthcare, and cubelet machines that make a small, soft, chewable cube. The cubelet and flake machines have an auger and a drive motor, so their problems are mechanical. Worn bearings, a scaled evaporator barrel and a leaking seal at the base are the usual calls. Dice cube machines behave like a conventional cuber and depend on a good water supply. We confirm the family on the data plate first, because the repair path for a crescent cuber is not the same as for a cubelet machine. Each family also uses its own cleaning chemistry and schedule.
Hoshizaki reach-in and undercounter refrigerators
Equipment guide
Seen on this line: Digital controller probe reading incorrectly / Defrost cycle set or wired wrong after a part change / Door gasket worn at the hinge side / Evaporator fan noisy or stalled
Hoshizaki also builds stainless reach-in and undercounter refrigerators and freezers, with an evaporator at the back or top and a self-contained system. The calls are the usual refrigeration ones with a Hoshizaki twist: electronic controllers with a temperature probe and defrost settings that need to be read before parts are replaced, door gaskets that wear at the hinge, and fan motors in the evaporator compartment. A digital controller can fail by reading incorrectly, and a technician checks the probe against a known thermometer. The units are tight, so airflow around the condenser is important, and units placed in a warm room need cleaning more often. They are used in sushi bars and small restaurants where the cabinet is the main protein and produce storage.
Finding the model and serial plate
Hoshizaki data plates are on the back or side of the machine, and on many ice machines there is also one inside behind the front panel. A model like KM followed by capacity digits identifies a crescent cuber, with letters for the cooling type, while F is a flaker and DCM is a cubelet machine. Have the full model, serial number, voltage and whether it is air, water or remote cooled, and any bin or dispenser model beneath it.
Parts
Hoshizaki parts are sold through its dealer and distributor network, and many parts are specific to the series and the generation of control board. Floats, thermistors, boards and evaporators are not interchangeable between families. Common wear parts such as pumps, contactors, fan motors and valves are available through distributors. We identify the series from the data plate, confirm the part, and quote after the diagnosis so you can approve the cost first.
Manufacturer warranty
If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.
See also
Same owner
Guides
More ice machines brands
Hoshizaki repair questions
What is a crescent cube and why does it matter for repair?
It is the half-moon cube Hoshizaki forms on a vertical stainless evaporator with individual cups. It matters because the machine ends the freeze using a thermistor and releases ice with hot gas plus water, so faults are traced to those parts instead of a probe.
Why will my Hoshizaki not refill with water?
A stuck or scaled float switch is the usual cause. The board does not see the reservoir fill, so it stops. A weak inlet valve, a clogged screen or low supply pressure can cause the same fault. Check the supply valve is fully open before calling.
Is the stainless evaporator easier to clean?
It is more resistant to some chemicals than plated evaporators, but it still scales. The manufacturer lists its own cleaner and descaler procedures by model, and mixing the wrong product can damage seals and plastic parts. Follow the label for dilution and contact time.
My Hoshizaki makes ice but the bin never fills. What is wrong?
Production is probably low because of a dirty condenser, a warm room, a weak pump or a scaled evaporator. Compare the ice from the last few cycles. If the cubes look thin or uneven, the thermistor or water flow is off.
Do Hoshizaki refrigerators use the same parts as the ice machines?
Not for the sealed system and controls. The refrigerators are separate designs with their own controllers, fans and gaskets. Some electrical parts are generic, but the controller and gasket are ordered by the refrigerator model.
