Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Globe slicer and mixer repair in the Twin Cities

On-site repair of Globe meat slicers and planetary mixers for delis, pizzerias, grocery counters and bakeries across Minneapolis and Saint Paul.

(651) 395-3422
Quick answer

What fails most often on Globe slicers and mixers?

On Globe slicers the usual failures are a dull or damaged blade, a worn sharpener assembly, loose carriage slide parts, and belt or motor problems that slow the blade. On Globe mixers the gear transmission, the attachment hub seal, the bowl guard interlock and the speed-shift linkage cause most calls.

About Globe equipment

Globe Food Equipment is based in Dayton, Ohio and has made slicers for more than a century, with mixers added as a second core line. That pairing is the key to servicing it: one belt-driven blade machine and one gear-driven planetary machine, both built to sit on a prep counter or floor and take daily abuse from delis, pizzerias, grocery meat departments and bakeries. Globe also sells a lower-cost line under the Chefmate by Globe name.

You see Globe slicers on deli counters in neighborhood grocers, in sandwich shops and in the back of house of restaurants slicing meats and cheeses. The mixers show up in pizzerias and small bakeries where a floor planetary mixer works dough every morning. Owners usually reach us when a blade stops cutting clean or a mixer starts leaking grease. Our pages on meat slicer repair and commercial mixer repair cover the equipment class, and Hobart is the brand most owners compare a Globe against.

Globe gravity-feed and manual slicers

Equipment guide

Meat Slicer Repair

Seen on this line: Blade slows or stops under load: glazed or loose drive belt / Dull edge that tears product: worn or misaligned sharpener stones / Stiff or sloppy carriage: residue or worn slide parts / Cracked guard or loose blade hub: take the machine out of use

A Globe slicer pulls product across a spinning round blade, with a thickness plate behind the blade setting the slice. The blade turns off a motor through a belt, so a worn or glazed belt shows up as a blade that slows under a heavy cut or stops while the motor hums. A built-in sharpener with two stones lets staff dress the blade edge, but stones wear down and the sharpener's alignment drifts, leaving a dull edge that tears product. The carriage slides on rods or a track that gather grease and meat residue, so the stroke gets stiff or loose. Ring guards and blade guards are safety parts and must be intact; a slicer with a damaged guard should not run.

Globe automatic slicers and electrical faults

Equipment guide

Meat Slicer Repair

Seen on this line: Carriage stops or overruns: worn gear or limit switch / Cuts out then restarts after a rest: motor thermal overload / Slice thickness drifts: gauge plate linkage out of adjustment / Switch or cord damage: unplug the machine and call

Automatic models add a motorized carriage on top of the blade drive, which means a second motor, a gear train and limit switches that control the stroke. A carriage that stops mid-stroke, skips or runs past its end points is usually a worn gear, a stuck limit switch or a loose drive connection. On both slicer types the electrical safety chain matters: a kickstand or gauge-plate interlock, a switch, and a motor that has thermal overload protection, which trips and resets after cooling. A slicer that cuts out after a few minutes of heavy use and then restarts is a motor or belt problem working too hard, not a mystery.

Globe planetary mixers

Seen on this line: Grease at the attachment hub: failed hub seal / Grinding or hesitation when shifting speeds: low or worn transmission grease and gears / Will not run with guard closed: interlock switch out of adjustment / Motor overheats on dough: overloaded bowl

A Globe planetary mixer turns a beater around the bowl through a gear transmission driven from a motor, with a hub on the front that accepts attachments such as a grinder or a slicer shredder. Wear shows up in the transmission and at the hub: grease that leaks from the hub is a failed seal, a transmission that grinds or hesitates when shifted is a sign of low or contaminated grease or worn gears, and a speed-change lever that will not seat is a linkage or gear wear problem. The bowl guard is wired to a safety interlock, and a mixer that will not run with the guard closed usually has a misadjusted or failed interlock switch. Overloading with stiff dough burns the motor and wears the gears, so what was in the bowl matters when we diagnose.

Finding the model and serial plate

Globe data plates are on the back or underside of the base on slicers and on the side or rear of the housing on mixers. They carry the model, serial number, voltage, amperage and horsepower or watts. Have the model and serial ready, along with the blade diameter on a slicer or the bowl size on a mixer. A photo of the plate and of any damaged guard helps us bring the right parts.

Parts

Globe parts come through the manufacturer's parts channel, and common slicer wear items such as blades, belts, sharpener stones and feet are also offered by commercial parts suppliers. Mixer transmission parts, hub seals and bowl-guard interlock switches are model-specific and are matched to serial number. Because a blade or guard is a safety item, we use the correct part for the model and do not substitute a look-alike.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Globe repair questions

My Globe slicer slows down halfway through a pound of cheese. Why?

A slowing blade under load points to a glazed or loose drive belt, or to a motor working near its limit. Cheese and fatty meats add drag, so a belt that is fine on lunch meat can slip on a block of provolone. Unplug the slicer before looking inside; the belt is a quick repair.

Can staff sharpen the blade themselves?

Staff can use the built-in sharpener the way the manual describes, and should do it with the carriage clear. If the edge stays dull after sharpening, the stones are worn or the sharpener is misaligned. Do not take a blade off the hub to grind it by hand; the blade is sharp and a damaged guard or hub is a safety issue.

Grease is dripping from the front of my Globe mixer. Is it dangerous?

It is not electrical, but grease in the bowl area can contaminate food. A leak at the attachment hub generally means the hub seal has failed. Stop using the mixer, wipe up what you can, keep food clear and call. The seal is a small part but the transmission needs checking while it is open.

Does a Chefmate by Globe slicer get serviced the same way?

Yes, the machine is similar in principle: a belt-driven blade, a gauge plate, a carriage and a sharpener. Parts are specific to the line, so the model plate matters. We confirm the model and the wear items before ordering so the repair matches the unit.

The mixer will not start unless I wiggle the bowl guard. What does that mean?

A guard that has to be held in a certain position points to a worn or misadjusted interlock switch, which tells the mixer the guard is closed. Do not tape or bypass it. The interlock is there so the beater cannot run with a hand in the bowl, and the adjustment or replacement is fast.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422