Star griddle, toaster and roller grill repair in the Twin Cities
Star equipment repair on site in the Twin Cities: griddles, conveyor toasters, hot dog roller grills, sandwich presses and heated display units.
What fails most often on Star countertop equipment?
On Star countertop equipment the usual failures are thermostats and infinite switches on griddles, heating elements and chain drives on conveyor toasters, roller motors and elements on hot dog roller grills, and worn cords and terminal blocks on everything that runs hot all day.
About Star equipment
Star is a countertop and light-line equipment brand: griddles, conveyor toasters, hot dog roller grills, sandwich and panini presses, hot dog steamers, nacho and pretzel warmers and heated merchandisers. In the Twin Cities you find them at convenience store food counters, concession stands, cafes, diners, school lines and in the back of many restaurants, where a roller grill or toaster has run for years with little more than a wipe-down.
Star equipment is simple and meant to be repaired. It is not a refrigeration or a sealed-vessel problem: the common failures are an element, a thermostat or switch, a motor and a drive chain, a cord and a terminal. The challenge is that the machines run all day at high temperature in a greasy environment, and the failures come from heat and grease at connections. A tech can usually diagnose with a meter on site. We handle the griddle work, the roller grill and toaster work and the food warmers and merchandisers in one visit. Nemco and APW Wyott make comparable equipment.
Star griddles
Equipment guide
Seen on this line: Thermostat or infinite switch failure / Burner or element cold zones / Grease in burner and terminal area
Star sells gas and electric griddles in countertop and equipment-stand versions, often with a thick steel plate and some with a chrome-plated surface. Gas models use burners under the plate with a manual valve and thermostat, and electric models use elements and an infinite switch or thermostat. The failures are a thermostat or infinite switch that no longer controls temperature, burners that do not light along their length, cold spots from a warped plate, and grease dripping into the burner or terminal area. Check the flat top with a surface thermometer, not by feel. Gas valve and pilot work is left to a technician.
Star conveyor toasters and roller grills
Equipment guide
Seen on this line: Element failure on toasters / Chain, gear motor and drive wear / Roller seizure and burnt cord ends
A conveyor toaster pulls bread or buns through radiant elements on a chain or belt driven by a gear motor, with a thermostat or controller setting speed and heat. The failures are a failed element, a stretched or jumping chain, a drive motor that stalls, and a controller or switch that no longer sets speed. A roller grill turns a set of heated rollers using a motor and a chain, with an element beneath, and fails with a seized roller, a dead motor, a broken chain or a burned element. Both lines fail where the heat and grease reach the wiring, so terminal blocks and cords are inspected on every call. Most of these are plug-in units and the first check is a clean cold start on a known-good outlet.
Star warmers, steamers and presses
Equipment guide
Seen on this line: Element or thermostat failure / Scaled or corroded steamer reservoir / Press hinges and hot plate wear
Star also makes heated display cases, hot dog and bun steamers, nacho cheese and pretzel warmers, and sandwich and panini presses. The faults are heating elements, thermostats, indicator lights that mislead, hinges on presses and hot plates, and water reservoirs that scale and corrode in steamers. A warmer that holds below safe temperature is a food safety issue, so we verify product temperature with a probe and not only the dial, and we recommend discarding product that has been held too cool. Steamer reservoirs are drained and descaled so scale does not coat the element.
Finding the model and serial plate
The Star rating plate is usually on the back, bottom or side of the unit and lists model, serial number, voltage, wattage or gas input. Countertop units can be hard to read because of grease, so wipe the plate clean first. Note the voltage and whether it is a plug-in unit or hard-wired, and tell the technician the brand line (for example griddle, toaster or roller grill).
Parts
Star parts come through the manufacturer and foodservice parts distributors. Elements, thermostats, infinite switches, motors, chains and rollers are ordered by model and serial number and voltage. Cords, terminal blocks and some switches are standard electrical parts. Availability varies by model and age, and we confirm the part number against the plate before anything is ordered.
Manufacturer warranty
If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.
See also
Guides
More cooking equipment brands
Star repair questions
Why does our roller grill burn the hot dogs on one side?
A roller that is not turning evenly or an element that is running hotter than the others. A seized roller, a worn chain or a burned element is the usual cause. Turn the unit off and let it cool before checking whether the rollers spin freely.
Why does the toaster come out light on one side?
One element has failed or the conveyor is running too fast for the heat setting. A technician checks both elements with a meter and looks at the chain tension. Crumbs on the elements are also worth clearing when the unit is cold and unplugged.
The griddle thermostat dial no longer matches the plate temperature. Why?
The thermostat or infinite switch has drifted or failed. Use a surface thermometer to see the true plate temperature, then call. Do not keep cooking against a dial you can no longer trust, because food ends up under or overcooked.
Can a hot dog roller grill be repaired or is replacement better?
Repair is usually reasonable for a motor, chain, element or switch. Replacement makes sense when the frame is corroded or rollers are pitted, since pitted rollers hold grease and are hard to keep sanitary. Ask for a written price first.
What is the burning smell from a new unit?
A little smoke the first few uses can be factory coating burning off. A smell that continues or a smell of burning plastic means shut the unit off and unplug it. Do not keep running it. A technician checks the cord, terminal block and element for damage.
