Nemco roller grill and countertop warmer repair in the Twin Cities
Nemco roller grill, countertop warmer, heated display and prep tool repair in the Twin Cities: elements, drive motors, controls and blade assemblies.
Why have the rollers on my Nemco roller grill stopped turning or heating?
Rollers that stop turning are almost always the drive: a failed gear motor, a worn chain or gears, or a switch that no longer passes power. Rollers that turn but stay cold point to a burned-out element or a bad heat control. A roller grill with a broken drive will still heat unevenly.
About Nemco equipment
Nemco is an Ohio-based maker of countertop equipment, and the machines are small, cheap to run and hard on their parts because they run for long hours at a counter. The best known are hot dog and sausage roller grills, heated display and warming equipment, and manual prep tools such as fry cutters and wedgers. We handle the electrical and motor side under food warmer repair and the heated-surface side as griddle repair when a unit has a heated plate.
These machines live at convenience store counters, concession stands, ballpark and stadium-style stands, deli counters, school lunch lines and food trucks. In c-stores a roller grill makes money all day, and a broken one often sits dark through the morning rush while the food is thrown away. Every failure is small and every repair needs a decision about value. A countertop unit with a failed drive might cost more to repair than to replace, and we say so directly before starting work.
Roller grills
Equipment guide
Seen on this line: Rollers stalled or jumping from worn gear motor or chain / Rollers rotate but do not heat / Seized roller or flaking non-stick surface
Roller grills combine a heat source with a set of rotating rollers driven by a motor, gears or chain. The drive is the most common failure: a gear motor that has stalled from fat and sugar creeping inside, a chain that stretches or jumps, a stripped drive gear or a roller that has seized on its bearing. Heat failures come from elements, infinite switches and thermal limits, and the symptom is a roller that turns but the dogs stay cool. Heat and rotation are separate circuits on most models, so a test of each separates the causes. Non-stick roller coatings wear and flake, and rollers with a worn surface mark and burst product. Cleaning chemicals trapped in the drive end shorten the motor's life.
Countertop warmers, heated displays and heat lamps
Equipment guide
Seen on this line: Element burned out or thermostat drifted / Fan or humidity pan faults in heated cases / Lamp sockets corroded, bulbs failing early
Nemco makes heated display cases, countertop warming shelves, bun and food warming units and heat lamps for pass-through and counter service. The elements, thermostats, switches and cords are simple parts, and most failures are a burned element or a failed control. Heated cases add a fan or a humidified chamber on some models, which brings a fan motor and a water pan into the list. Heat lamp holders corrode where moisture reaches the socket, and bulbs fail from vibration. Because these units hold food, a thermostat that has drifted is a food safety problem, not just a performance one, since the dial may show hot while the food sits below the safe holding temperature.
Heated plates, toasters and prep tools
Equipment guide
Seen on this line: Plate not heating or cycling wrong / Blade assembly dull, bent or cracked / Mount loose on wall or table
Nemco's range also includes small electric cooking and toasting equipment with a heated plate or platen, and its Easy-series manual prep tools, which are mechanical and rely on blades and pushers rather than power. Heated plates fail like any griddle: elements, thermostats and contactors. The prep tools fail because the blade assembly dulls or bends, the pusher head cracks and the frame loosens at its mounting. A blade set is a replacement part, and a bent one cuts unevenly and wedges produce. Because the tools mount to a wall or table, a loose mount is a safety issue, and we tighten or reset it before returning it to use.
Finding the model and serial plate
On a Nemco roller grill the rating plate is usually on the underside or back of the base, and on warmers on the back or bottom. Note the model number, the serial, voltage and wattage. For a roller grill record the number of rollers. For prep tools the model is often stamped on the frame or sold by blade set size, so have the blade size ready.
Parts
Nemco parts for elements, switches, thermostats, gear motors, chains and roller assemblies are sold through the manufacturer and equipment parts distributors, and many are specific to the roller grill series and the number of rollers. Blades and pusher heads for prep tools are sold as sets. Lead times vary by part. We check the parts cost against the replacement cost before we proceed on a low-cost countertop unit.
Manufacturer warranty
If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.
See also
Nemco repair questions
My roller grill heats but the rollers do not turn. What now?
That is a drive failure: a seized gear motor, a stretched or broken chain, or a stripped gear. Fat and sugar inside the drive housing often caused it. Unplug it before looking inside, and do not force a roller that is stuck.
Why do my hot dogs cook unevenly on the rollers?
Uneven color usually means some rollers are not turning at the same speed, a worn non-stick surface or an element that has failed in one zone. A technician checks each circuit separately so the right part is replaced.
Can a Nemco countertop warmer be left on overnight?
Follow the manufacturer's guidance for the model. Running a unit empty or dry can burn the element or a moisture pan, and leftover food held unsafe is a food safety risk. Turn it off and clean it at close.
Is it worth repairing a small countertop unit?
Sometimes. A new element or switch is usually worthwhile on a unit that is otherwise sound. A failed motor plus worn rollers and a corroded housing often is not. We give you the written price before work starts so you can decide.
Why does my Nemco fry cutter cut crooked?
A dull or bent blade set, a cracked pusher head or a loose mount causes crooked cuts. The blade set is the replaceable part, and the mount should be re-secured so the force of the pull does not shift the tool.
