Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Electrolux Professional combi, dishwashing and laundry repair in the Twin Cities

Electrolux Professional combi oven, dishwasher and commercial laundry repair in Minneapolis and St. Paul: steam systems, scale, pumps, drums and controls.

(651) 395-3422
Quick answer

What fails most often on Electrolux Professional combi ovens and washers?

On combi ovens it is scale in the steam system, door gaskets, fan motors and humidity or core probes. On dishwashers it is wash pumps, spray arms, drain and fill valves, and heaters. On laundry it is drum bearings, door locks, drain valves and control faults. Water quality drives most of these.

About Electrolux Professional equipment

Electrolux Professional is a Swedish company, headquartered in Stockholm, that makes combi ovens, dishwashing systems and commercial laundry under one name, and it sells its laundry range under brands such as Wascomat. The reach of the line is the point: one maker, three trades, and three different repair skill sets. How common each line is in the Twin Cities varies, so this page is built around how each is made and what wears, rather than assuming what you have. See our combi oven repair, commercial dishwasher repair and commercial laundry repair pages for the category detail.

You tend to meet the combi ovens in hotels, hospitals, senior-living and corporate kitchens, the dishwashing equipment in the same dining operations, and the laundry equipment in on-premises laundries at hotels, healthcare facilities, apartment buildings and laundromats. European-designed equipment shows its origin in its construction: compact stainless cabinets, electronic controls, and a heavy dependence on water treatment. Hard water and untreated supply cause most of the early failures we see on this kind of equipment, regardless of the model.

SkyLine and Air-O-Steam combi ovens

Equipment guide

Combi Oven Repair

Seen on this line: Scaled steam system, weak steam and long cook times / Door gasket leaking steam / Fan motor noise or core probe failure

A combi oven cooks with hot air, steam or both, and Electrolux Professional's SkyLine and earlier Air-O-Steam ovens follow that pattern. The steam system is where most calls begin: depending on the model, steam comes from a boiler or from water sprayed on the heated fan chamber, and scale blocks either one. Scale causes weak steam, long cook times, over-filling and fault stops. Door gaskets harden and leak steam. Fan motors and their bearings fail from heat and moisture, humidity and core temperature probes read wrong or break, and the cleaning system's spray lines clog if the wrong chemical or tablet is used. Descaling and the water filter are the maintenance that decides how long the oven lasts.

Dishwashing systems

Seen on this line: Spray arms scaled, poor wash results / Drain pump, fill valve or wash pump faults / Rinse temperature low from weak heater or booster

Electrolux Professional's warewashing range includes undercounter, hood-type and conveyor machines. The failure list matches any commercial dishwasher but is sharper where the water is hard. Wash and rinse spray arms clog with scale and food and give poor cleaning, wash pumps and seals wear, drain pumps and fill valves stick, and heating elements and boosters scale over. Chemical injection tubing for detergent and rinse aid collapses or clogs, and the machine runs but does not clean or sanitize. Wash and final-rinse temperature is the compliance measure, and a heater that has weakened shows up as a rinse that is below the sanitizing requirement. See our guide on a dishwasher that will not drain.

Wascomat and commercial laundry

Seen on this line: Drum bearing or seal wear, noise and leaks / Door lock, interlock or drain valve faults / Board or program control faults

Electrolux Professional's laundry range covers washer-extractors and dryers, sold under Wascomat among others. On the commercial washer side the wear is mechanical: drum bearings and seals, shock absorbers or suspension, door locks and interlocks, drain valves and supply valves. A washer that bangs or walks is a suspension or bearing question, and one that will not drain is a valve or pump problem. Controls vary from simple programmers to microprocessor boards, and a board fault is a different repair from a mechanical one. On the dryer side, covered in commercial dryer repair, gas ignition, lint and airflow, belts and heating elements are the usual causes. Check the lint filter and vent first.

Finding the model and serial plate

Electrolux Professional equipment carries a rating plate showing the model, serial number, voltage, phase and rating, usually on the rear or side of the cabinet, and on combi ovens often on the side panel or near the supply connections. Laundry machines carry it on the back panel. Record the full model and serial, note which product family it is, and have the last fault message ready. Mention the water hardness if you know it.

Parts

Electrolux Professional parts are sourced through the manufacturer's service network and parts distributors, and boards, probes, steam generators, spray arms and pumps are typically specific to the model and series. Standard items such as gaskets, valves and filters are more available. Because it is a global product line, some parts come from outside the US, and lead times vary. We confirm the model and serial before ordering and tell you when a part is a longer order.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Electrolux Professional repair questions

Why does my combi oven give weak steam?

Scale in the steam generator or spray system is the usual reason. It also causes long cook times and fault stops. Descaling on schedule and using the water filter prevent it. A weak door gasket will leak steam and look similar.

Does water hardness really matter this much?

Yes. Scale builds on every heated surface and in every valve and spray nozzle, and it is the leading cause of early failure in combi ovens and dishwashers. A water filter and a regular descale cost less than the repairs they avoid.

Why does my dishwasher run but leave dishes dirty?

Clogged spray arms, a weak wash pump, low wash temperature or a chemical feed that has failed are the usual causes. Check that the arms spin freely and that detergent is feeding. Temperature and chemical feed need a technician's test.

My laundry washer shakes violently during the spin. What is wrong?

An unbalanced load, failed suspension or worn bearings can all cause it. Stop the machine, because a bad bearing can damage the drum or the frame. A technician checks the mounts, the shock absorbers and the bearing play before it runs again.

Do you handle all three product types?

We repair combi ovens, commercial dishwashers and commercial laundry equipment, and we tell you at diagnosis which part of the machine is failing. Equipment under manufacturer's warranty is best handled through the manufacturer's network first.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422