Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Restaurant appliance repair in Minneapolis and St. Paul

On-site restaurant appliance repair in Minneapolis, St. Paul and the surrounding suburbs: line equipment, walk-ins, ice machines and dish machines.

(651) 395-3422
Quick answer

How do I get restaurant equipment repaired without losing a service?

Call at the first sign of trouble, not after the failure. Tell us the make, model and symptom, and what you can still run without the unit. We diagnose on site, give you a written price to approve before work starts, and can schedule around your service hours where the schedule allows.

Restaurants: what is different

A restaurant kitchen runs its equipment harder than almost any other business. A fryer battery cycles all day, a flat top sits at full heat for ten hours, and a reach-in on the line is opened hundreds of times a shift. Parts that would last years in a quiet setting wear out in months. The failures are rarely random. A thermostat that drifts, a gasket that no longer seals, a condenser packed with grease dust: each one gives warning before it stops the line.

What separates a good repair visit in a restaurant from a bad one is timing and diagnosis. A tech who arrives during prep and leaves before the dinner push has done the job right, even if the part took a second trip. We repair commercial refrigeration, cooking equipment, ice machines and dish machines on site, and we give you the diagnosis and a written price before any repair starts. We are an independent company and not the manufacturer.

Equipment that matters in restaurants

  • Walk-In Cooler Repair

    The walk-in holds most of your inventory, so one warm night can cost more than any other failure. Evaporator fans, door gaskets and defrost controls are the usual causes.

  • Commercial Refrigerator Repair

    Line reach-ins are opened constantly in a hot kitchen, which loads the condenser and wears the door gaskets and hinges faster than anywhere else in the building.

  • Prep Table Repair

    Sandwich and pizza prep tables hold cut and portioned food at the station. A rail that drifts above 41°F means pulling product during service.

  • Commercial Fryer Repair

    Fryers fail on the thermostat, high-limit and gas valve side, and a bad probe can mean oil that runs off temperature without any alarm.

  • Commercial Range Repair

    Burner ports clog with boil-over and grease, and oven pilots and thermostats drift under daily heat. A range down takes out saute, the oven below it, or both.

  • Commercial Griddle Repair

    Flat tops lose heat unevenly when a burner or thermostat fails, and the cold zone shows up as inconsistent searing before anyone calls.

  • Ice Machine Repair

    Restaurants go through ice for drinks, bar service and sometimes cold holding. Scale in a hard-water machine slows production exactly when the dining room fills.

  • Commercial Dishwasher Repair

    If the dish machine will not reach rinse temperature or will not drain, the kitchen runs out of clean plates and glasses within a service.

  • Restaurant Equipment Repair

    For a kitchen with several problems at once, one whole-kitchen visit sorts out what to fix first and what can wait.

What shapes a repair visit here

The Friday rush

A unit that works at 2 p.m. can fail at 7 p.m. because the load changes. A compressor that copes with half-empty shelves quits when the door is open every minute. We ask when the problem shows up, because a failure that appears only under rush load points to heat, airflow or a weak part rather than a dead one.

Grease and heat in every cabinet

Kitchen air carries grease, flour and heat into condensers and fan motors. A reach-in under a hot line can sit in a pocket of warm air all day. Many callouts come down to a coil that has not been cleaned, which is cheaper to prevent than to repair. We note the condition when we are in there and say plainly what the kitchen is doing to the equipment.

Menu-driven equipment mix

A pizza place, a steakhouse and a ramen shop have almost nothing in common underneath. One leans on deck ovens and dough mixers, another on charbroilers and salamanders, another on steam and stock kettles. The failure pattern follows the menu, so we ask what you cook and how much of it comes from each piece before we guess at a cause.

Tight kitchens and limited access

Many Twin Cities restaurants sit in older buildings with small kitchens, shared basement walk-ins and equipment wedged into corners. Pulling a unit to reach a valve or board is a real job. Telling us about access up front, including the loading route and where we can stage parts, saves time on the day.

Staff turnover and unclear history

The person who knew why the walk-in door sticks may have left last month. Without a repair history, the same fault gets patched repeatedly. We write down what we find and what we did, so the next cook or manager has something to go on, and so a repeat fault is obvious when it shows up.

Fitting the visit around the operation

Restaurants are not like offices, so the visit has to fit the shift. When you call we tell you the earliest opening we have, and where the schedule allows we can come between lunch and dinner or before the kitchen opens. If the equipment is the thing running the line, say so on the call. Tell us which units are still working, so we can plan around the dead one. Have a manager or lead cook on hand who can approve the written price.

Inspections and food safety

Health inspectors check cold holding at 41°F or below and hot holding at 135°F or above, as set out in the FDA Food Code and the Minnesota Food Code (Minn. Rules chapter 4626). A walk-in that runs warm or a hot-hold unit that will not hold temperature is a violation waiting to be written, and it is also a food loss. Dish machines are inspected for sanitizing too. Exhaust hoods and fire suppression are separate systems and fall outside our work.

Brands we see most

Guides

Other kinds of operation

Restaurants questions

Which restaurant equipment breaks most often?

In most kitchens it is refrigeration and the equipment that runs all day under heat: reach-ins, prep rails, fryers, and the dish machine. Ice machines fail often too because water quality wears them down. Burners, thermostats, gaskets and fan motors are the parts we replace most.

Can you repair a unit while the kitchen is still cooking?

Often yes, if the unit can be isolated. A walk-in compressor or a reach-in can usually be worked on while the line runs. Gas fryers and ranges mean shutting that appliance off. Tell us which units you can lose and for how long, and we plan the visit around that.

My prep table keeps reading 45°F. What should I check?

Check that the lid is closed, the pans are not blocking the air vents, and the condenser area is clear of dust. If the table still reads above 41°F, move the food and call. A failed fan or a weak compressor is not a check you should attempt yourself.

Do you fix exhaust hoods and fire suppression?

We fix the hood and its exhaust fan and make-up air, along with the ranges, fryers, griddles, charbroilers and ovens under it. Fire suppression systems, grease-duct cleaning and gas piping go to the specialists. If a gas smell appears, leave the building and call the gas utility from outside.

Is it worth repairing an old fryer or reach-in?

It depends on what failed and how often. A gasket or fan motor on a sound unit is a normal repair. A cracked tank, a failed sealed system on an old refrigerator, or repeated failures in one season push toward replacement. We say so in the written diagnosis.

Sources

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422