Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Hatco toaster, food warmer and booster heater repair in the Twin Cities

Hatco conveyor toasters, Glo-Ray warmers, holding cabinets and booster water heaters repaired on site across Minneapolis and St. Paul.

(651) 395-3422
Quick answer

What goes wrong with Hatco toasters, warmers and booster heaters?

Hatco conveyor toasters fail at the drive motor, chain and elements. Glo-Ray heat lamps and strip heaters fail at bulbs, elements and ballasts. Booster heaters fail at the heating elements, thermostat, high limit and pressure relief valve, and they are often tied to a dishmachine rinse temperature problem.

About Hatco equipment

Hatco Corporation, based in Milwaukee, Wisconsin, makes a narrow set of equipment that shows up in nearly every kind of kitchen: conveyor toasters, Glo-Ray infrared warmers, holding cabinets and booster water heaters. In the Twin Cities that covers hotel breakfast buffets, school cafeterias, coffee shops, delis, hospital kitchens and any dish room that needs a 180-degree final rinse. A jammed conveyor toaster or a food warmer and holding cabinet that will not hold temperature is the typical first call.

Hatco equipment is repaired part by part. Toasters are mechanical and electrical, with a motor, a chain or belt, elements and a thermostat. Infrared warmers are simple but depend on bulbs and ballasts. Booster heaters carry the most risk, because they are pressurized hot water devices tied to a dishwasher. If a booster heater is the cause of a sanitizing failure, it needs a correct diagnosis, not a guess, before anyone touches the wiring.

Hatco Glo-Ray warmers and holding cabinets

Seen on this line: Glo-Ray lamp or strip heater will not light / Cabinet will not reach or hold temperature / Door gasket torn or door will not seal / Switch, socket or ballast failure

Hatco Glo-Ray warmers are infrared strip heaters and lamps that hold food at serving temperature under a heat source above the counter. The common failures are bulbs, element strips, lamp sockets that burn from heat, and ballasts or switches that fail before the heater does. Holding cabinets add a thermostat or digital control, a heating element and a blower, and a door gasket that, once torn, lets the cabinet lose heat and hold uneven temperatures. If a cabinet reads right on the display but holds cold in the corners, check the gasket and the air path before the control. A lamp that flickers or buzzes often points at a socket or a connection, not the lamp itself.

Hatco conveyor toasters

Equipment guide

Conveyor Oven Repair

Seen on this line: Conveyor stalls, slips or runs slowly / Toast comes out pale on top or bottom / Elements burned out or sagging / Speed control or thermostat drift

Hatco conveyor toasters, including the Toast-Qwik line, run bread through a heating chamber on a chain or belt driven by a gearmotor. Common wear points are the drive motor, the chain and sprockets, the speed control and the elements above and below the conveyor. Crumbs and sugar burn onto the elements and the chain and slow everything down, so a toaster that is under-toasting may need cleaning before any part replacement. A chain that has stretched slips and skips under load. When the conveyor stops but the elements stay hot, shut it down: a stalled conveyor over live elements burns product and can damage the chamber. Elements and thermostats are replaced by matching the model and wattage.

Hatco booster water heaters

Seen on this line: Final rinse will not reach temperature / High limit trips repeatedly / Pressure relief valve drips or weeps / Element or contactor failure from scale

A booster heater raises incoming hot water to the final rinse temperature a dishmachine needs. It is a small pressurized tank with electric elements, a thermostat, a high-limit and a pressure relief valve. A booster that cannot reach temperature is usually a failed element, a fouled thermostat or a high-limit that has tripped, but the cause may also be low incoming water temperature or a failing contactor. Hard water scales the elements, and a pressure relief valve that drips should never be plugged. Booster work involves 208 to 480 volts and pressurized hot water, so it is not an operator repair. Call before opening a panel.

Finding the model and serial plate

The Hatco data plate lists the model, serial number, voltage, phase and wattage. On toasters and warmers it is typically on the back or underside of the unit, and on booster heaters it is on the side of the jacket or the control panel. Booster heaters are often wired into the building, so note the voltage and phase from the plate rather than guessing. Our model number guide shows where else to look if the plate is covered.

Parts

Hatco parts include elements, bulbs, sockets, switches, thermostats, relays, drive motors, chains and gaskets, and many are specific to a model and wattage. Booster heater elements and thermostats are matched by the model and serial from the data plate. We use OEM parts where fit matters and a suitable equivalent where it does not. Lead times depend on the supplier and the part, and we confirm the part number against the plate before ordering.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Hatco repair questions

Why does my Hatco toaster toast only one side of the bread?

The top or bottom element has probably failed, or the element is coated with burned sugar and crumbs. Look at the chamber with the unit off and cool. A dark element in one bank points at a failed element, but wiring and the thermostat can also cause it, so call if cleaning does not fix it.

My booster heater leaves the dishmachine rinse too cool. What should I check?

Check that the machine is getting hot incoming water, because the booster only raises it. Do not open panels or reset a high-limit more than once. A repeated trip or a drip from the pressure relief valve means stop and call, since this is pressurized hot water at high voltage.

Do Glo-Ray warmers need a special bulb?

Yes. They use infrared heat lamps or strip elements rated for the fixture, and the wrong lamp can overheat the socket or cook the product. Replace bulbs with the type listed on the data plate or in the manual, and turn the unit off and let it cool first.

How can I tell if a holding cabinet is losing heat through the door?

A torn or hardened gasket is the first thing to inspect. Close the door on a strip of paper; if it slides out easily, the seal is weak. A cabinet that holds the set temperature at the sensor but cold at the door side often has a gasket problem, not a control problem.

Can a toaster chain be cleaned, or does it need replacing?

Burned-on residue can often be cleaned off with the unit unplugged and cool. A chain that has stretched, kinked or lost links needs to be replaced, and so do worn sprockets. A conveyor that keeps slipping under normal load is a sign that cleaning alone will not solve it.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422