Glastender underbar and back bar repair in the Twin Cities
Repair for Glastender back bar refrigerators, bottle boxes, underbar ice bins, cold plates and draft coolers at Twin Cities bars, taprooms and restaurants.
What goes wrong with Glastender underbar and back bar equipment?
Glastender problems are typically clogged ice-bin and sink drains, leaking or iced-over cold plates, sticky gaskets on bottle boxes and back bar coolers, fouled condensers, and draft coolers that run warm. Because bars are built to order, the first step is identifying the exact layout.
About Glastender equipment
Glastender is a Saginaw, Michigan manufacturer of bar equipment: back bar refrigerators, bottle boxes, underbar workstations with ice bins and cold plates, sinks and drainboards, draft beer coolers and related stainless fabrications. It builds many items to order for a particular bar layout, so two bars with the same brand name may have different equipment. You see it in bars, taprooms and restaurants that wanted the bar built as one piece.
A Glastender repair is partly refrigeration and partly plumbing and fabrication. A cold plate is a refrigeration part sitting in a pile of ice. An ice bin drain is a plumbing part tied to a floor sink. A bottle box is a cooler built into a stainless frame. Ask what is actually failing, and sort it into cooling, drainage or draft. That is also how we scope a bar cooler repair before the visit.
Glastender back bar refrigerators and bottle boxes
Equipment guide
Seen on this line: Gasket or lid seal worn / Drain line clogged / Condensing unit starved of air / Evaporator fan blocked or failed
Back bar refrigerators and bottle boxes hold bottles within reach of the bartender. Bottle boxes sit low in the bar, often with lids or sliding doors, and take spilled liquid and dropped caps. Gaskets harden or tear, drain lines clog and the condensing unit, often tucked in a cabinet or under the bar, gets less airflow than it needs. If the unit is built into the bar, ventilation is the first question. Warm product on one side with cold product on the other points to a blocked fan or airflow path inside the box.
Glastender underbar ice bins, cold plates and drains
Equipment guide
Seen on this line: Cold plate leaking or iced over / Ice bin drain clogged / Product line not chilling / Fittings loose at sinks and drainboards
Underbar workstations put an ice bin where the bartender works, often with a cold plate in the bin so soda or beer lines are chilled by ice or by refrigerated glycol. Cold plates can leak at the fittings or corrode, and lines through them can freeze or bring warm product. Ice bin drains clog with melted ice and sugar, flooding the floor sink and the bar floor. Speed rails, drainboards and sinks are stainless and last, but their seams and fittings loosen. A bin full of water is usually a drain, not a refrigeration problem.
Glastender draft beer coolers
Equipment guide
Seen on this line: Evaporator fan or thermostat failed / Beer foaming from line or gas problem / Condenser restricted / Long-run line warming beer
Draft coolers and keg boxes keep kegs cold and feed towers or taps. When beer warms, look at the cooler first: evaporator fan, thermostat, gasket and condenser airflow. When beer foams with cold kegs, look at gas pressure, lines and couplers. Long runs from keg to tap add heat that a cooler cannot fix. If the bar uses a long-draw system with glycol, the issue may sit in the cooling loop. A tech should confirm which system you have before measuring, because the fix differs for each, and ask when the lines were last cleaned.
Finding the model and serial plate
Glastender equipment is usually built per project, so the data plate and any project or order number matter. Look On the cabinet interior or the back-bar frame for the model, serial number, refrigerant and electrical data. Also note the bar's configuration: how many sections, whether it has cold plates, where the condensing unit sits and what the drains connect to. A sketch or photo of the bar layout with the plate shot saves a second trip.
Parts
Glastender parts split into refrigeration, stainless and plumbing items. Refrigeration parts such as fan motors, compressors, thermostats and heaters are common components with many equivalents. Doors, gaskets, lids, cold plates and fabricated pieces are specific to the model and may be built for the job, so we match them from the plate, measurements and photos. Availability varies with age and supplier. Some bar lineups include glass-handling equipment, so check the plate to see who built each machine.
Manufacturer warranty
If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.
See also
Glastender repair questions
Why is my underbar ice bin full of water?
The ice bin drain is usually blocked by melted ice and sugar, or the drain line has lost its pitch. Clear what you can reach safely and have the drain line checked. A full bin is rarely a refrigeration fault.
How do I know if a cold plate is leaking?
Signs are unexplained water in the bin, product that no longer chills, ice that forms unevenly or lines that freeze. Pressure-test the lines before replacing the plate. Do not cut into the ice bin yourself; call for service.
My bottle box is warm only at one end. What is happening?
Airflow inside the box is probably blocked or an evaporator fan has failed. Bottles stacked against the discharge can also cause it. Rearrange the load and check that the fan turns. If it does not, have it tested.
Can I swap a bar section from another brand into my bar?
Not easily. Bar equipment is built to specific sizes and fittings. Swapping a section can affect drain connections, electrical circuits and the line-up. Measure everything, including the drain locations and the electrical circuit, and talk through options before ordering anything that has to fit.
Who services the glasswasher in my Glastender bar?
Check the nameplate on the glasswasher itself. It may be a Glastender product or a machine from another maker installed in the bar. Commercial glasswashers are repaired by the plate, so photograph it and we can tell you what we would need to see before a visit.
