Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Perlick bar cooler and draft beer repair in the Twin Cities

Repair for Perlick back bar coolers, draft beer coolers and towers, glass frosters and bottle merchandisers at Twin Cities bars, taprooms and restaurants.

(651) 395-3422
Quick answer

What commonly goes wrong with Perlick bar coolers and draft systems?

Perlick bar problems are usually dirty gaskets and condensers, drain and condensate trouble, glass frosters that frost over or stop cooling, and draft issues such as foaming from warm beer, a failed fan or a leaking faucet. Draft gas and line cleaning problems often get blamed on the cooler.

About Perlick equipment

Perlick is a Milwaukee, Wisconsin company that has made its name on bar refrigeration: back bar and undercounter coolers, bottle coolers, glass chillers and frosters, direct-draw draft beer coolers, towers and faucets. Because the product is beer and the customer is watching the tap, Perlick shows up in bars and breweries, taprooms, stadium concessions and restaurants with serious beer programs, where a night without cold beer is a night of lost sales.

The tricky part of a Perlick call is that the cooler and the draft system are two systems that share one box. Beer that pours foamy is often blamed on the compressor when the fault is a warm keg line, a wrong gas pressure or a dirty line. Warm bottles are a refrigeration fault. We separate the refrigeration from the dispensing before we start, which is the difference between a bar cooler repair and a draft system problem that no cooler part will fix.

Perlick back bar and undercounter coolers

Seen on this line: Gaskets crusted with spills / Door tracks jammed with debris / Condensate drain blocked / Condenser packed with dust and paper

These units hold bottles and cans behind or under the bar. They run in a hostile place: spilled beer and syrup crust on gaskets, ice and glass fall into the door tracks, and the condenser breathes bottle-cap dust and paper. Sliding doors and their tracks wear, swinging doors lose self-closing, and the condensate drain gets clogged with sugar. When a cooler fills with water, check the drain before the evaporator. Bars that close late have no natural cleaning window, so condenser maintenance falls behind, and the unit that ran fine in winter fails during a July weekend.

Perlick draft beer coolers and towers

Seen on this line: Beer foaming from warm line or tower / Evaporator or tower fan failed / Faucet leaking or sticking / Regulator or coupler faulty

A direct-draw draft cooler keeps kegs cold and sends beer to a tower a short run away. Faults appear in three places. In the cooler, a weak or stopped evaporator fan lets the box warm. In the tower, a cooling fan or a poorly insulated run lets beer warm on its way to the faucet. In the gas and lines, regulators, couplers and dirty beer lines cause foam. A faucet that sticks or leaks needs rebuild or replacement, which is routine on a bar that cleans lines on schedule. Foamy pours with a cold keg are usually not a refrigeration issue.

Perlick glass frosters and glass-door merchandisers

Seen on this line: Frost forming too heavily on glass / Defrost cycle incomplete / Door seal leaking / Anti-sweat heater failed

Glass frosters chill mugs well below freezing, so frost forms on the glass. They fail when the defrost cycle does not complete, when the door seal leaks, or when the unit is overloaded with wet glasses straight from the washer. Glass-door merchandisers show bottles to customers, and fogging glass, failed lighting and fan faults are what staff notice. If the glass fogs, look at the door seal and the anti-sweat heater. If frost builds on frosters, look at the seals and the defrost control, not the glass, and keep wet glasses from going straight in.

Finding the model and serial plate

On a Perlick unit the data plate is typically inside the cabinet on an interior wall or in the compressor compartment, and it lists model, serial number, refrigerant and electrical data. For draft equipment, also note the tower type, how many faucets it has, the kind of coupler on the keg and whether it is direct draw. Photograph the plate and the tower. When foam is the complaint, note keg temperature, gas pressure and when the lines were last cleaned.

Parts

Perlick refrigeration parts split into cabinet and sealed-system parts. Doors, gaskets, hinges, tracks and shelving are matched to the model, so we read the plate. Compressors, fan motors, heaters and controls are common refrigeration components with many equivalents. Faucets and tower parts are sold through draft parts suppliers, and a faucet rebuild may be possible instead of replacement. Availability varies. We confirm the part and the supplier's answer before you approve work.

Manufacturer warranty

If this equipment is still under the manufacturer's warranty, it should usually go through the manufacturer's authorized service network first. We are an independent company and not the manufacturer.

See also

Perlick repair questions

My beer pours foamy. Is the cooler broken?

Not necessarily. Check keg temperature first. If kegs are cold, look at gas pressure, a kinked or warm line, a dirty line or a faulty coupler. A foaming faucet may need a rebuild. Warm bottles and warm kegs are the refrigeration faults.

Why does my glass froster build so much frost?

Wet glasses straight from the washer add moisture, and door seal leaks add more. A defrost cycle that does not complete lets ice grow. Let glassware drain, check the door seal and have the defrost control tested.

The back bar cooler is full of water. What do I check?

The condensate drain. Sugar and debris clog it, and the pan overflows into the cabinet. Move product, clear the drain line and look at the pan. If it clogs repeatedly, there may be a pitch or a connection problem.

How often should I clean the condenser on a bar cooler?

Often enough that you can see the fins. Bars create dust and paper at the condenser, so a monthly look is reasonable. If the fins are matted, brush and vacuum with power off and clearance open.

Can the same tech fix the cooler and the faucet?

The cooler, yes. A faucet rebuild is a simple repair if the parts are on hand. Line cleaning and gas balance are part of draft maintenance, and we will tell you if the problem is the dispensing system rather than the cooler.

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422