Open 24/7, 365 days a yearMinneapolis & St. Paul, MNCommercial Only
(651) 395-3422

Film on bar glasses: identify the residue, then test for beer clean

Cloudy, spotted or foam-killing bar glasses: identify protein film, sanitizer residue, lime film or etching, and test for a beer-clean glass.

(651) 395-3422
Quick answer

What is the residue on my bar glasses, and how do I test for a beer-clean glass?

Read the glass before touching the machine. Water that beads or salt that clings in patches means an invisible film, usually grease, protein or detergent. Foam that will not hold points to residue the eye cannot see, often sanitizer. White haze that follows dried water is mineral, and haze that never clears is etching.

What can be left on a glass that has just been washed?

A glass can fail for five different reasons, and each leaves a different trace. Grease or protein film comes from lipstick, hand oil, cream drinks and milk-based cocktails, and it is nearly invisible. Detergent or rinse-aid residue is a film left when chemistry is rinsed off poorly or fed too strong. Sanitizer residue is the one that kills foam without showing anything on the glass. Mineral film is a white or gray haze that forms where hard water dried. Etching is permanent damage to the glass itself.

The Brewers Association's Draught Beer Quality Manual sets the standard: glassware must be free of visible soil and marks, and a beer-clean glass is also free of foam-killing residues and lingering aromatics such as sanitizer. That is a stricter test than a dish has to pass, which is why a machine that is fine for kitchen ware can still send bad glasses to the bar. The repair side of the machine, with its pumps, drains and heaters, is on the glasswasher repair page. This guide is about reading what the glass tells you.

Read the evidence in order: how water behaves on the glass, how salt behaves, how foam behaves, then how the glass looks and smells once it is dry. The answers separate the five causes before anyone touches a dial or a chemical container. A bar that runs a separate kitchen machine will find its drain and door faults on the commercial dishwasher repair page.

How do the sheeting, salt and lacing tests read a glass?

The Brewers Association manual describes three tests for beer-clean glass. In the sheeting test, you dip the glass in water. If the glass is clean, water evenly coats it when lifted out; if an invisible film remains, water breaks up into droplets on the inside surface. In the salt test, salt sprinkled on the inside of a wet glass sticks evenly to a clean surface but does not stick to the parts that still carry a greasy film, so poorly cleaned glasses show an uneven distribution of salt. In the lacing test, the glass is filled with beer: foam on a clean glass clings in parallel rings after each sip, while on a poorly cleaned one it clings in a random pattern or not at all.

Each test catches something the others miss. Sheeting and salt find film on the glass. Lacing finds the residue that does not show on water at all, because it is the beer's foam that is sensitive to it. A glass that sheets and takes salt evenly but still pours a collapsing head has failed on something other than grease, and sanitizer is the first suspect. That is why the lacing test matters even when the first two look good.

Run the tests on a glass from the rack position that has given trouble, after a full cycle, and let it air dry first. The manual calls for air-drying because a towel can leave lint and transmit germs and odors, and it says to store glasses on a stainless wire basket instead of a towel or a smooth rubber pad. A towel-dried glass can fail a test for reasons that have nothing to do with the machine.

Is the film protein or grease, and what removes it?

Protein and grease films stick to glass and resist a short, cool cycle. Lipstick wax and cream drinks are the worst offenders, and a glass that leaves the machine with a patchy salt test is usually carrying one of them. The causes sit on the wash side: detergent too weak or the wrong kind, a wash that is too cool, spray that never reaches the base of the glass, or a bar that never scrapes and dumps glasses before loading them.

The manual's rules for the wash are plain. Detergent must not be fat- or oil-based, and low-foam glassware detergents are sold through restaurant and bar suppliers. For automatic machines it recommends dedicating the machine to bar and beer glassware, not subjecting it to food or dairy residue, and using water temperatures of 130°F to 140°F, with high-temperature machines designed for 180°F usable without added chemical sanitizer. Hobart's LX manual, for one maker, tells the user to check that the sump temperature shown during the wash is above 120°F on chemical-sanitizing machines and above 150°F on high-temperature machines. Those figures differ because they belong to different documents and machines, so the machine's data plate and the chemical supplier's setting are the numbers to follow.

Beer residue poured into the wash tub, or a lipstick-heavy rush that loads dozens of glasses at once, overwhelms a small machine. Emptying glasses to a drain first, scrubbing lipstick off the rim before the cycle and letting the machine recover its temperature between loads all reduce film without a repair. If a film persists with fresh detergent, a correct wash temperature and a clear spray, the feed pump or the heater needs a technician.

Is sanitizer or rinse aid killing the foam?

Sanitizer is a deliberate residue, and the line between enough and too much is narrow. The manual says excess sanitizer does not do a better job than the correct concentration and may be unhealthy for staff and customers. For a three-tub sink it gives 100 ppm for chlorine and 200 ppm for quats unless the local authority requires otherwise. Minnesota's rule on chemical sanitizing, part 4626.0805, sets chlorine at a minimum of 50 ppm unless the product label says otherwise, at 75°F or above when the solution pH is 8 or below, and 100°F or above when pH is 8.1 to 10. The point for beer is that more is not better: a glass can be properly sanitized and still taste of chlorine.

On an automatic machine the sanitizer and the rinse aid are metered by pumps, and the manual says to check detergent, sanitizer and rinse-agent concentrations once each day using kits or the chemical supplier's recommendations. A glass that smells of sanitizer, a pour that tastes of it, or foam that will not lace points at a feed that is set too strong or a rinse cut short. Weak rinse-aid feed gives slow drying and spots, and Hobart's LX troubleshooting lists an inoperative rinse-aid pump among its causes of spotting. Too much of either leaves its own film.

Setting the feeds is the chemical supplier's job (a daily concentration check also belongs in the maintenance checklist), because the right concentration depends on the water, the machine and the product. Adding extra detergent by hand, mixing a stronger sanitizer in the sink or running a different chemical through the machine usually makes the film worse. When the supplier has changed products recently, mention it, since a different detergent or rinse aid can change how beer holds a head.

Is a white haze scale, or is the glass etched?

Mineral film follows the water. It shows as a white or gray haze, often in the pattern where drops dried, and it tends to be worse on a rack position under a clogged rinse nozzle. Hobart's LX manual lists hard water as a cause of spotting and says to install a water softener and use a rinse agent. A softener treats the water for the whole machine, and descaling treats the heater and nozzles that scale has already coated.

Etching is different, because it is damage and not a deposit. Hobart's manual says etching is usually caused by any combination of high temperatures, soft water, soft glass or highly alkaline washing solutions. Etched glass stays cloudy after any cleaning, and the chemistry or temperature that caused it has to change to protect the next glass. A haze that does not clear after the supplier's descaler and a thorough rinse is more likely etching than scale.

The practical sorting is by pattern and persistence. Haze that follows drying marks and returns when the glass dries again is mineral. Haze that stays exactly the same after every treatment is etching. Spots in the same position on every rack are a clogged nozzle or a wash arm that catches, which a technician clears with the power off.

What the glass showsLikely residueNext step and who
Water beads, salt clings in patches, foam rings are brokenGrease, protein or lipstick filmCheck wash temperature and detergent with the supplier; technician if the feed or heater is at fault
Water sheets and salt is even, but the head collapsesSanitizer or rinse-aid residueSupplier checks feed concentrations with test strips
Glass smells or tastes of chlorineSanitizer fed too strong or rinse cut shortSupplier resets the feed; technician if the pump is stuck
White haze that follows drying marksHard water mineral film, low rinse aidSoftener, rinse aid and descaling; plumber or supplier for the water
Haze that never changes after treatmentEtching from heat, soft water, soft glass or strong alkalinitySupplier reviews chemistry; the glass stays marked
Same spots on every rack positionClogged nozzle or wash armTechnician, with the power off
Film that returns within a day of a chemical changeNew product or new settingSupplier, who set it

A safe sequence to follow

  1. Air-dry a glass from the problem rack position

    Let it dry on a wire rack, not a towel, so lint and odors do not skew the tests.

  2. Run the sheeting test

    Dip the glass in water and lift it out; an even coat is clean, droplets mean a film.

  3. Run the salt test

    Sprinkle salt inside a wet glass and see whether it clings evenly or leaves bare patches.

  4. Run the lacing test

    Pour beer and watch whether foam leaves parallel rings after each sip or a random pattern.

  5. Smell the glass and read the sanitizer strip

    Note any chlorine odor and the strip reading from the machine's rinse or the sink bath.

  6. Write down the result and hand it over

    Record which tests failed and when the problem began, then give the supplier or technician the list.

When to stop and call

  • Chemical feed tubes run full of air, a pump runs but nothing moves, or a container empties much faster than before
  • The wash or rinse temperature will not reach the data plate figure
  • The same film or spots return within a day of the chemical supplier adjusting the machine
  • The same rack positions come out spotted after the nozzles and arms are clear
  • Water leaks, tripped breakers or glass jams point to a mechanical fault

Questions about this problem

Why does a glass pass the sheeting test but still pour flat?

Sheeting finds film that shows on water. The Brewers Association manual says a beer-clean glass is also free of foam-killing residues and aromatics such as sanitizer, which do not always show on water. Check the sanitizer strength and smell the glass, then run the lacing test with beer.

Why shouldn't glasses be dried with a towel?

The Brewers Association manual calls for air-drying because a towel can leave lint and may transmit germs and odors. It also says to dry and store glasses on a stainless wire basket, not on a towel or a rubber drain pad, since smooth surfaces transfer odors and slow drying.

What wash water temperature does a bar glasswasher need?

The Brewers Association manual gives 130°F to 140°F for automatic machines, with high-temperature models designed for 180°F usable without added chemical sanitizer. Hobart's LX manual wants the sump above 120°F on chemical machines and above 150°F on high-temperature ones. The data plate on your machine governs.

Is cloudy glass always hard water?

No. Hard water leaves a mineral haze that follows drying marks, but etching also looks cloudy and is permanent. Hobart's manual ties etching to high temperatures, soft water, soft glass or highly alkaline washing solutions. A haze that does not clear after descaling is more likely etching.

How often should the chemical concentrations be checked?

The Brewers Association manual says to check detergent, sanitizer and rinse-agent concentrations once each day with test kits, or to follow the chemical supplier's recommendations. A check at the start of the shift catches an empty container or a dead pump before a rush of bad glasses.

Sources

Call with the model and what it is doing

You hear the earliest opening on the phone. After the diagnosis you get a written price to approve before any repair starts.

(651) 395-3422
Call (651) 395-3422