Ice machine cleaning and sanitizing in Minneapolis and St. Paul
Ice machine cleaning and sanitizing in Minneapolis and St. Paul: the descale-then-sanitize order and what Manitowoc, Hoshizaki and Scotsman require.
What is the correct order for cleaning and sanitizing a commercial ice machine?
Descale first, then sanitize, as two separate steps with separate chemicals, and always by the manufacturer's own procedure. Manitowoc, Hoshizaki and Scotsman all follow that order but differ on the products, the quantities, which parts are washed by hand and whether the sanitizer is rinsed. The sheet for your exact model controls.
What an ice machine cleaning visit involves
Ice is a food, and the machine that makes it is a food-contact surface with a part nobody sees: a water path that stays wet for years. Minnesota's food rules require the enclosed parts of an ice maker, and the bin, to be cleaned at the frequency the manufacturer specifies, or often enough to keep soil and mold from building up where the manufacturer names none. Staff can wipe a bin. Descaling and sanitizing the water system is a sequenced procedure with set chemicals, set quantities and timed cycles, and the three biggest makers each write it differently.
Frequency is whatever the model's manual says: some makers specify at least once a year, others every six months, and hard water, yeast or heavy use call for more often. This page covers the cleaning half of the work: scale versus slime, why descaler and sanitizer never share a step, what each maker tells a technician to remove and soak, and what the bin and dispenser need. How often is answered in the ice machine cleaning schedule guide. Filters, condensers and sensors belong to a different visit, described under ice machine maintenance. A machine that has already stopped making ice starts with ice machine repair.
What an ice machine cleaning visit covers
- Modular cuber on a bin
Head and bin are two jobs. Manitowoc's Indigo NXT procedure has the technician pull the splash shields, ice thickness probes, water distribution tubes, ice dampers, water trough shield and the pump and level probe, soak the plastic parts, then run a clean cycle and a separate sanitize cycle.
- Cuber sitting on a dispenser
Dispenser power comes off first. Manitowoc says not to begin cleaning until line voltage is disconnected from the machine and any dispenser, and Hoshizaki's KM-1301 to KM-2500 sheet turns the dispenser off once leftover ice is dispensed and back on after cleaning. The dispenser liner is washed with the bin.
- Nugget and flake machine
Scotsman's Prodigy nugget and flake sheet is one scale-removal run: 8 ounces of its scale remover in 3 quarts of warm water goes into the reservoir with the photo eyes covered, and the machine stops itself after 40 minutes. Ice made during the run is discarded or melted.
- Large modular cuber (quantities by model)
Quantities and contact times are model-specific, and the cleaning sheet for the exact model controls. Even inside one Hoshizaki sheet, the KM-1301 to KM-2500 sheet, the sanitizing bleach is 3.75 fluid ounces for the KM-1601 and smaller and 5 for the KM-1900 and larger, so a quantity copied from another model or another maker is wrong. Undercounter and small cubers have their own sheets with their own figures.
- Cuber with a manual cleaning valve
Some Hoshizaki cubers add a valve that is opened to send solution through the evaporator and closed again for ice making. The sheet says the machine will not work unless the valve is turned completely closed, so a missed step shows up as no ice after a cleaning.
What the visit finds and what we do about it
| Finding | Why it develops | What is done |
|---|---|---|
| White or tan scale on the evaporator and water parts | Hardness minerals in the supply water coat the evaporator, distribution tubes, pump and probes as water circulates. Manitowoc describes its cleaner as the product that removes lime scale and mineral deposits. | The descale cycle circulates the maker's cleaner through the machine. Manitowoc's sheet also soaks removed plastic parts in 16 ounces of its cleaner per gallon of potable water for 10 to 15 minutes, with a soft-bristle brush on heavy scale. |
| Scale-coated ice thickness sensor and water level probes | Scotsman's maintenance aid notes that the ice thickness sensor becomes coated with mineral scale, and that left untreated this changes the thickness of the ice bridge. Probes and the plastic insulator brackets collect the same crust. | The metal sensor is separated from its plastic insulator, wiped and scrubbed with diluted scale remover, rinsed with clean water, blown dry and reassembled. Water level probes get the same treatment. |
| Slime on the bin liner, door, chute or splash shields | Manitowoc describes its sanitizer as the step that disinfects and removes algae and slime. The descaler does not do that job, so a machine that was descaled but not sanitized can still carry it. | Scotsman washes the freezing compartment parts and the bin liner with the sanitizer solution and flushes the bin drain with hot water. The underside of the bin door and the corners are where a quick wipe misses, and they need hand work. |
| Foam, residue or an off smell after a do-it-yourself cleaning | Hoshizaki's KM-1301 to KM-2500 sheet specifies chlorine bleach without additives, because additives cause excessive foaming and reduce cleaning effectiveness, and it warns that ammonia-type cleaners can damage the ice maker. | The product the sheet names goes in, in the quantity for that model, with the foaming waited out where the sheet says to (one minute on the KM-1301 to KM-2500 sheet) and the rinse the maker requires. |
| Plated evaporator exposed to the wrong acid | Some evaporators are nickel-plated or tin-plated, and Nu-Calgon sells a descaler rated safe for nickel- and tin-plated evaporators. A harsh general-purpose acid is a gamble on those surfaces. | Each maker's sheet names its own descaler, and that named product is what goes in the machine. If a third-party descaler is ever considered, the model's manual decides, not the label on the jug. |
| Cleaning valve left open or the pump run dry | Hoshizaki's KM-1301 to KM-2500 sheet warns not to leave the control switch on WASH for long periods with an empty water tank because it damages the water pump seals, and that the machine will not make ice until the cleaning valve is fully closed. | The steps are run in order with timed checks: tank refilled, valve closed, switch back to ICE, and a check that the machine drops into a normal freeze cycle before the visit ends. |
| Ice from the cleaning run left in the bin | Cycles make ice while solution circulates. Scotsman's nugget and flake sheet says to discard or melt ice made during cleaning (its cuber sheets say to discard the bin's ice at the start and the first batch afterward), and Nu-Calgon's directions say to discard the first batch after the machine returns to service. | The bin is emptied before the cycle starts, as all three makers instruct, and the first batch is thrown out or melted. The scoop and bin are wiped before ice is served again. |
| Wet electrical parts during hand-cleaning | Manitowoc warns against soaking the pump motor, allows only the impeller and housing below the red line to go in liquid, and says electrical connectors must never be exposed to liquids. | Power is disconnected before any part comes out. Gloves and goggles go on, as Manitowoc's sheet requires for descaler and sanitizer, and connectors are kept dry until the water level probe gasket seats against the base. |
Before the visit
- Find the cleaning sheet or manual for your model number and write down when the machine was last descaled and last sanitized. The two are separate dates, and many machines only ever get one.
- Plan for the ice already in the bin. Manitowoc, Hoshizaki and Scotsman all begin by emptying it, so every cube goes. Have sealed bagged ice on hand for the service and keep it off the floor.
- Do not pour any cleaner into the machine ahead of the visit. Quantities and timing are set by the model, and Hoshizaki warns that ammonia-type cleaners can damage the ice maker.
- Note whether the machine sits on a dispenser and where the dispenser's switch or breaker is, so its power can be shut off before work starts.
- Look into the bin with a flashlight and note where you see film, spots or an odor: the door underside, the chute, the scoop holder. Those are the places that need hand-cleaning time.
Stop at gas valves, 208, 240 or 480 volt wiring, sealed refrigerant circuits, steam under pressure and anything live. Those are a call.
How long the equipment is out of use
Plan on the machine and its bin being out of service for the whole visit. The cycles alone run long: 35 minutes each for the descale and sanitize on a Scotsman Prodigy Plus, about 30 minutes for the clean cycle on a Manitowoc Indigo NXT, and 30 minutes of cleaner plus 45 of sanitizer on Hoshizaki's large KM sheet, all before its rinses. Hand-cleaning of parts and the bin fills the gaps between them. Book it for a closing shift or after the lunch rush, and stock sealed bagged ice beforehand.
Between visits
- Wash your hands before taking ice and use the plastic scoop that came with the bin. Hoshizaki's KM-1300 manual says to keep the scoop clean with a neutral cleaner and a thorough rinse, and that the bin is for ice only.
- Do not store anything in the bin, not bottles, not cases, not a thermometer. Hoshizaki's KM-1300 manual says the storage bin is for ice use only.
- Clean the bin liner and the dispenser liner with a neutral cleaner such as dish soap and rinse thoroughly, as Hoshizaki's KM-1301 to KM-2500 sheet lists, and never with an ammonia-type cleaner.
- Keep a dated log of every descale, sanitize and filter change, with the product used. Minnesota's rule ties frequency to the manufacturer's specification, so the log is how you show you followed it.
When maintenance is not enough
Cleaning restores a machine; it does not repair one. Manitowoc's sheet says that within the hardness range allowed for potable water, descaling should not be needed more often than every two months, so scale that returns faster points at the water supply, an exhausted filter or a fault in the machine. A distribution tube that will not stay clean, a bin liner that holds moisture or an evaporator that keeps scaling is a part question, and the ice machine repair page covers those. When cleaning cycles keep being repeated just to get clear ice, the repair or replace guide is the next read.
Ice machine cleanings by brand
Related to ice machine cleaning
Repairs for this equipment
Related pages
Where it matters most
Where we service ice machine cleanings
- Ice machine cleaning service in Chanhassen, MN
- Ice machine cleaning service in Chaska, MN
- Ice machine cleaning service in Columbia Heights, MN
- Ice machine cleaning service in Coon Rapids, MN
- Ice machine cleaning service in Cottage Grove, MN
- Ice machine cleaning service in Crystal, MN
- Ice machine cleaning service in Eagan, MN
- Ice machine cleaning service in Eden Prairie, MN
- Ice machine cleaning service in Edina, MN
- Ice machine cleaning service in Elk River, MN
- Ice machine cleaning service in Farmington, MN
- Ice machine cleaning service in Forest Lake, MN
Other maintenance and cleaning visits
Questions about ice machine cleanings
Do Manitowoc, Hoshizaki and Scotsman sanitize the same way?
No. Manitowoc classifies its sanitizer as no-rinse, so sanitized surfaces are not rinsed. Hoshizaki's KM-1301 to KM-2500 sheet uses chlorine bleach without additives, then three rinse passes. Scotsman runs a sanitizer cycle and has the technician wash the freezing compartment parts and bin liner with the sanitizer solution. The model's own sheet decides.
Can descaler and sanitizer go in together to save a cycle?
The three makers run them as separate steps in a fixed order, descaler first and sanitizer second. Manitowoc's sheet even keeps them in separate sink compartments for hand-soaked parts and prompts a separate clean and sanitize cycle. None of the sheets offers combining them as a shortcut.
What does the Minnesota food code require for ice machine cleaning?
Minnesota Rules part 4626.0845 requires the enclosed components of equipment such as ice makers, and ice bins, to be cleaned at the frequency the manufacturer specifies. Where the manufacturer specifies none, the rule requires a frequency that prevents soil or mold from accumulating.
Do I throw away the ice after a cleaning?
Yes, in two places. All three makers have the bin emptied before the procedure starts, and Scotsman's nugget and flake sheet says to discard or melt any ice made during cleaning. Nu-Calgon's descaler directions add that the first batch after the machine returns to service is discarded as well.
Which cleaning jobs can my staff do and which belong to a technician?
Scotsman says most Prodigy maintenance should be done by technicians, but lists the water filter change, air filter cleaning and bin cleaning and sanitizing as owner tasks. Hoshizaki's KM-1300 manual says only qualified service technicians should service the icemaker. Manitowoc recommends an authorized service company for its detailed procedure.
What else do Minnesota rules say about ice that an inspector can check?
Ice used as food or as a cooling medium must be made from drinking water (part 4626.0195). Ice used to cool the outside of food cannot then be served as food (part 4626.0260). Liquid waste drain lines must not pass through an ice machine or ice storage bin (part 4626.0595).
Sources
- Manitowoc Indigo NXT detailed descaling and sanitizing procedures (MII_SB_0033)
- Hoshizaki KM-1301 to KM-2500 ice machine cleaning and sanitizing sheet
- Hoshizaki KM-1300 instruction manual
- Scotsman Prodigy Plus cubers maintenance aid (291-856)
- Scotsman Prodigy flaked and nugget maintenance aid (291-857)
- Nu-Calgon Nickel-Safe Ice Machine Cleaner
- Minnesota Rules 4626.0845, cleaning frequency of equipment food-contact surfaces
- Minnesota Rules 4626.0195, ice
- Minnesota Rules 4626.0260, ice used as exterior coolant
- Minnesota Rules 4626.0595, ice units and separation of drains
- Minnesota Rules 4626.0020, definitions (food includes ice)

